A portion of a medium-weight concrete masonry unit was tested for absorption and moisture content and produced the following results: mass of unit as received = 5435 gsaturated mass of unit = 5776 goven-dry mass of unit = 5091 gimmersed mass of unit = 2973 gCalculate the absorption in kg/m3and the moisture content of the unit as apercent of total absorption. Does the absorption meet the ASTM C90 requirement for absorption?

Q: Why is it important that the concrete masonry units meet certain absorp- 811 a tion requirements? h…

A:

Q: Calculate the volumes of the hydration products for 150 gm of cement with 0.5 w/c ratio, assume…

A: It is required to determine the volume of dry cement actually hydrated. Vcah=Weight of dry cement…

Q: What is the minimum strength that concrete must reach prior to freezing so that the overall strength…

A: The minimum strength that concrete mus overall strength gain is not affected:

Q: Example 6: Design a concrete mix for slab with dimension of (5x5x2.5) according to ACI by Volumatic…

A: Given data: 1- characteristic compressive strength at 28  days fmin = 30 MPa 2- Nominal maximum size…

Q: A trial concrete mix is to be prepared for a garage floor which is subjected to freezing. and…

A: Solution: Concrete Mix Design: The required strength = 32 MPa Standard Deviation = 1.5 Coarse…

Q: y consider the following data for concrete with mild exposure, calculate the quantity of cemer…

A: Given:Volume of water=191.6 litreWater cement ratio=0.5

Q: Write any five difference between Ordinary Portland Cement and Pozzolana Portland Cement

A: Ordinary Portland Cement (OPC): A blend of limestone and raw materials, such as gypsum,…

Q: A sample unit of concrete masonry is recieved having a mass of 10.4kg. The unit is tested using ASTM…

A: Given: The received mass of units is 10.4 kg. The standard mass of the unit is 11.1 kg. The dry mass…

Q: A trial concrete mix is to be prepared for a garage floor which is subjected to freezing. and…

A:

Q: The strength of a sample of matured concrete is found to be 34.5MPa. Find the strength of identical…

A: In this question, we have to calculate the strength of concrete at the age of 14 days. The formula…

Q: 1. (a) The data presented below is compiled to obtain the modulus of rupture values of the MgO…

A:

Q: (b) All basic chemical composition of Portland cement reacts with different rate of hydration. List…

A:

Q: a) Chemical deterioration. b) Physical deterioration c) all of them 9- Map cracking of concrete is…

A: Note :- as per guidelines only first three can be answered. Please repost remaining as separate…

Q: nstruction: Please provide complete solutions and box final answers.

A: S.no  Strength in Mpa  Mean  (X-mean) (x-mean)^2         1 38.3 41.735 -3.435 11.799225   3.074275…

Q: A concrete mix for a concrete beam exposed to mild climate is to be designed according to the ACI…

A: Answer  Mix proportioning using ACI absolute volume method. Step (1) Calculate Required average…

Q: Using the following data for n unreinforced Portland Cement Concrete pool deck: Design strength f'c=…

A: (a) The formula to calculate the compressive strength is given by, fm=fc+1.65σ              ...1…

Q: Write four aggregate properties that affect the compressive strength of concrete. (3 P)

A: Four aggregate property that affect the compressive strength of concrete: 1. Size of the aggregate…

Q: On the 28th day after concrete was mixed, a 6.00-in-diameter concrete cylinder failed in a…

A: Given data, Diameter of cylinder d = 6 in Compressive load P = 145000 lb Factor of safety γ0 = 5

Q: A concrete masonry unit tested as follows: 8,893 g 9,354 g Determine the absorption and moisture…

A: Given: The saturated mass is 10,089 g. The oven dry mass is 8,893 g. The field mass is 9,354 g.

Q: 4) Design a concrete mix for the following condition and constraints using the absolute volume…

A: The given data is: Design strength=27.6 Mpa Standard deviation=4 MPa Assuming the following: Target…

Q: Design the concrete mix according to the following conditions: het Design Environment Pavement slab,…

A: Given, Design strength (f'c) = 5000 psi  Admixture dose = 0.15 fl oz/1% air/100 lb

Q: Design a concrete mix for the following conditions and constraints using the absolute volume method…

A: ACI MIX DESIGN METHOD: Fck=25.1 Mpa S=2.8 MPa Fm=25.1+1.64(2.8) Fm=29.692 Mpa Selecting the  W/C…

Q: When conducting a laboratory test on brick samples, the following results were obtained: 8…

A: According to the Iraq standard no.25, The grades of bricks can be classified into three grades. They…

Q: A concrete masonry unit was tested according to ASTM C140 procedure and produce the following…

A:

Q: From the knowledge of the effects of GGBS, PFA and microsilica, indicate whether their inclusion to…

A: Required to find: How the presence of GGBS, PFA and microsilica effect the  a) Alkali silica…

Q: Design a concrete mix for the following conditions and constraints using the Absolute Volume Method.…

A: Given  Required Design Compressive Strength (f'c) = 27.6 MPa Standard Deviation of Compressive…

Q: Me lesio Q4) Concrete is required for walls of a building that will be moderately exposed to…

A: Mix Design as per ACI 211.91 Compressive strength = 21.5 MPa Slump = 50 mm Cement - type I Aggregate…

Q: Calculate the average density of brick. ?

A: Brick No. Length mm Width mm Depth mm Mass kg 1 213 98 70 2.52 2 212 98 70 2.5 3 211…

Q: The rate of evaporation of water from concrete mix as time thus loss of water leads to less…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Subject: Concrete technology Q: a)What are the disadvantages of using calcium chloride in Portland…

A: Portland cement is the most common type of cement that is generally used throughout the world as a…

Q: A portion of a normal-weight concrete masonry unit was tested for absorption and moisture content…

A: ASTM C140  Mass of unit as received, Mo = 7024 g Saturated mass of Unit, Msat 7401 g Oven-dry mass…

Q: Controlling excessive temperature gradients in large concrete masses is very crucial. Explain in…

A: After the placement of the concrete, monitoring the temperature of concrete is one of the most…

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.