i need the answer quickly A pneumatic displacement gage has d, =0.762 mm and d =1.575 mm. The supplypressure is 68919.7 Pa with a random fluctuation of t483 Pa, and the differentialpressure P, - P, is measured with a water manometer that may be read with anuncertainty of 12.44 Pa. Calculate the uncertainty in the dimensional measurementusing both: a) non-analytical method, and b) analytical method.%3!If u 100 % sure in all part then u try because wrong answer gives u downvotes

Answered: Image /qna-images/answer/a344cae7-1fb1-474b-a2d5-1023128071ad.jpg

Answered: A pneumatic displacement gage has d,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please and explain step by step, instructions given at top
LESSON: AUTODESK FUSION 360 Choose from the choices below:
Solve show all steps and solution. Energy systems engineering
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
MENG364 MANUFACTURING TECHNOLOGY please solve the question very quickly Student Number 124544
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
Topics: Statics of Rigid Bodies, Equilibrium of Rigid Bodies, Equilibrium in Two Dimensions, etc. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” THANK YOU FOR YOUR HELP. PS: If you have answered this already, don’t answer it again; give chance to other experts to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times. If you answer it again, i'll dislike all your entries/answers.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A pneumatic displacement gage has d, -0.762 mm and d, -1.575 mm. The supply pressure is 68919.7 Pa with a random fluctuation of +483 Pa, and the differential