A plant has a load of 290 kilowatt with an average power factor of 70 % lagging. The owner request you to correct the power factor to reduce its power consumption. How much capacitor in kVAR is required to increase the power factor to 90% lagging?

Q: can sameone solve this thanks

A: In this question we will try to find the true power delivered to the load as shown below.

Q: 11 kV at a power factor of 0.867lagging. Each machine supplies half the total power. The synchronous…

A:

Q: Q1. For 'Load at Unity Power Factor' example discussed in the lecture (see figure below), find power…

A:

Q: Three coils each having resistance of 14 0 are connected in delta across 414 V, 50 Hz supply. Then…

A:

Q: If the base kVA is 25,000 then a 5000 KVA alternator with 8% reactance will have Select one: OaA 4%…

A: Given, Base kVA, SBnew=25000 kVA. Alternator kVA, SBold=5000 kVA. Reactance, Xold=8%.

Q: Q1/ Find the RMS value of lo in the unbalanced three-phase circuit. 0.40 j20 a 1.60 j4 A 780 1540…

A: The solution can be achieved as follows.

Q: When 40V DC voltage is applied to a single-phase AC motor, it draws 1A current. When 200v-50Hz AC is…

A:

Q: SINE(0 6Vp-p 1.5K) R₁ LL 2.5 mH 100 PL On the load, find the Power (P) in Watts (W) R A 180//180 Ω…

A: Given Data: A series RL circuit with, Peak-to-peak voltage Vpp=6 V Frequency f=1.5 kHz To Find:…

Q: Question: For the basic chopper circuit Edc= 50 V, R= 80 ohms, duty cycle is 30% then the average…

A:

Q: For the circuit shown in figure beside, find the total average power delivered to the circuit? * J5…

A:

Q: Determine the capacitor necessary to increase the power factor by 20% the loads are: P1= 100KW,…

A: Given    Loads:P1=100 kw,pf=0.707P2=50 kw ,pf=0.6VL=480 volts rmsRL=0.1 Ωf=60 Hz

Q: two 3phase alternators in parallel are both operating at the same frequency. What is theremedy if…

A: Parallel operation of Alternator AC power systems are often interconnected for efficiency, reliable…

Q: Three coils each having resistance of 30 Q are connected in star across 427 V, 50 Hz supply. Then…

A: total power consumed = 3×Phase voltage2Resistance for star connection, phase voltage = line voltage3

Q: Question. In the following circuit, calculate Vai, Va2, Va3, Vo1, Vo2, Vo3, V+, V., and Vo. I, +10 V…

A: NOTE: Since you have posted a question with multiple subparts, we will solve the first three…

Q: Determine the power and the rms value (300mt+) (a) 5 сos (300лt+

A: In this question, we need to determine the power and rms value of the given signal. We know, RMS…

Q: Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of…

A: Given data: $37 data at memory location $C100ACCA=$B8ACCB=$FE

Q: 4 0 -is n 6 0 -j8 N js n 220/-30° V Figure 3. Referring to figure 3, determine the rms current at…

A:

Q: 13. A circuit is composed of a resistance of 22 ohms, an inductance of 0.11 henry and a capacitance…

A:

Q: 30 412 V2 + Va2 i3 + R3 Va3 Va4 is 60 20V R, V4=3V1 R5 16 Rg 40 30 20 10A 2+ i7 ğımsız akım…

A: The current source given in the figure is the independent, & it is DC source The instantaneous…

Q: The voltage-flux adjustment of a certain single phase 220 V induction watthour meter is altered so…

A: Given: Supply voltage, V = 220 V The meter is altered so that phase angle between flux and applied…

Q: For the circuit of Figure, assume the source operates at a frequency of 100 rad/s. Calculate the…

A: In this questionWe need to determine the power in 100 ohm resistance.We are solving this problem…

Q: One of the following is not a law for power factor calculation. O P/S O cose O Q/P O P/VI

A:

Q: What is the value of the equivelent impedance? 250 j1SA w m 302 20 j102 51.09 +9.8j 0.46+0.21j…

A: Choose the correct option Find the equivalent impedance across the terminal as shwon in the figure.…

Q: Question: What is a logic gate in digital electronics, and how does it work?

A: We need to explain what is a logic gate in digital electronics, and how does it work .

Q: A capacitor is connected across a 120 V, 60 Hz supply. An ammeter indicates 5 A and a wattmeter…

A: Voltage across the capacitor

Q: Distinguish the different kinds of quantities and description of power in alternating current…

A:

Q: Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must…

A:

Q: A 30 kVARS capacitor bank is

A:

Q: What is the value of real power supplied by the source in the figure? ww 30/0° V ms 42 5252.8 None…

A: Given circuit,

Q: Determine the power factor, true power, reactive power, and apparent power in the circuit. 1 k ohm…

A:

Q: In an AC circuit when a KVAR is equal to KW value, it indicates to O Maximum power factor Minimum…

A: The power factor of any circuit measures how effective the active power is being utilized. In the…

Q: A pump station uses an induction motor that requires a complex power of S1 = 55<30° kVAand a…

A:

Q: Three coils each having resistance of 26 Q are connected in star across 438 V, 50 Hz supply. Then…

A: Need to find power

Q: reactive power calculation.

A:

Q: An electrodynamometer type wattmeter is used to measure power in 1-o circuit. The connected load…

A: The solution is given below

Q: What is the capacitance to be connected in parallel with the load to increase the power factor to…

A:

Q: Calculate the complex power S for all the four circuit elements. 1652 Vs=18√240v rms Value 3j6s2…

A: The given problem is from circuits. The detailed solution is given in the next step

Q: A Load absorbs 10 kVA at a lagging power factor of 0.6. The complex power is: Select one: a. 2000+…

A: The correct solution is given below

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.