A piston-cylinder assembly contains 2 Ib of water, initially at 100 lbf/in.2 and 400°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 50%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu. Part A Determine the work for the constant-pressure process, in Btu.

A piston-cylinder assembly contains 2 Ib of water, initially at 100 lbf/in.2 and 400°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 50%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu. Part A Determine the work for the constant-pressure process, in Btu.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A piston-cylinder assembly with stops (see figure) contains 1.54 kg of water initially occupying a volume of 1.25 m at a pressure of 1 bar (State 1). As the water in the assembly is heated, the pressure and temperature in the system remain constant until the piston contacts the stops. In this position (State 2), the quality, x2, is determined to be 92%. Heat continues to be added to the system at a constant volume until the system reaches a pressure of 1.5 bar (State 3). Determine the following quantities: а. X b. V2 (m2) C. W13 (kJ) d. Qu (kJ) e. Plot the results on a P-v diagram, labelling relevant P, T, and v values.
1. A tank containing 250 kg of kerosene is to be heated from 20°C to 40 °C in 15 minutes, using 4 bar steam. The kerosene has a specific heat capacity of 2.0 kJ/kg-°C.over that temperature range. ha at 4.0 bar is 2,108.1 kJ/kg. The tank is well insulated and heat losses are negligible. Determine the rate of heat transfer required and steam flow.
Carbon dioxide (CO₂) fills a closed, rigid tank fitted with a paddle wheel, initially at 80°F, 50 lb/in², and a volume of 1.6 ft³. The gas is stirred until its temperature is 500°F. During this process heat transfer from the gas to its surroundings occurs in an amount 2.6 Btu. Assume ideal gas behavior, but do not assume constant specific heats. Kinetic and potential energy effects can be ignored. Determine the mass of the carbon dioxide, in lb, and the work, in Btu.
7777
A piston-cylinder assembly contains ammonia, initially at a temperature of -20°C and a quality of 80%. The ammonia is slowly heated to a final state where the pressure is 6 bar and the temperature is 120°C. While the ammonia is heated, its pressure varies linearly with specific volume. For the ammonia, determine the work and heat transfer, each in kJ/kg.
Fast.
2. An ideal gas in a piston/cylinder system undergoes a process in which the specific volume is increased. In which process is the most work done for the same volume change? a. Isobaric process b. Isothermal process C. Isentropic process, k = 1.4 d. Polytropic process, n = 2 e. Cannot tell from this information
B. 0.5 kg of a nitrogen contained within a piston-cylinder undergoes a constant-pressure process at 4 bar beginning at tn 0,72 m/kg. For the nitrogen as the system, the work is =- 84 kJ. Determine the final volume of the nitrogen, in m.
Five lbs of propane is contained in a closed, rigid tank initially at 80 lbf/in.2, 50°F. Heat transfer occurs until the final temperature in the tank is 0°F. Kinetic and potential energy effects are negligible. Determine the amount of energy transfer by heat, in Btu. Q= i Btu
7
7