A piston-cylinder assembly contains 2 lb of water, initially at 100 lbf/in.² and 350°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 50%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu.

A piston-cylinder assembly contains 2 lb of water, initially at 100 lbf/in.² and 350°F. The water undergoes two processes in series: a constant-pressure process followed by a constant volume process. At the end of the constant-volume process, the temperature is 300°F and the water is a two-phase liquid-vapor mixture with a quality of 50%. Neglect kinetic and potential energy effects. Determine the work and heat transfer for each process, all in Btu.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ql- mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area. The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, Force - kN 75 90 | 105 120 131 125 110 25 50 4.7 Extension-mm 0.02 0.04 0.06 0.20 - 0.60 1.60 3.00 4.0 Fracture
Calculate to the correct number of significant figures. (9443+45-9.9)x8.1x10^6
16. There are 4 materials that were exposed to different forces and their corresponding elongation is given. Which will have the greatest and lowest value of k. Material A was exposed to 100 N force and elongation is 0.02 meters. B was exposed to 200 N force and elongation is 0.05 meters. C was exposed to a force of 300 N and elongation is 0.07 meter, D was exposed to 400N force and elongation is 0.09 meter.
Question 9 Answer the following questions. Show your work on a separate paper. Round your responses to 3 significant figures. Include appropriate units. Provide magnitude and direction where appropriate. The 4.5 Mg truck shown below collides with the 1.75 Mg car. After the collision, they move forward together. Answer the following questions. 30 km/h 10 km/h 38) What is the combined velocity of the truck and the car just after impact? Show your work. Solution Units Direction 3b) What is the coefficient of restitution of the impact? Show your work or justify your response on a separate piece of paper. Solution Units
Which of the followings can be found out by calculating the area only under the linear portion (elastic region) and the area under the whole stress strain graph on the same graph? A ) Resillience - Toughness B ) Hardness - Toughness C ) Endurance - Strength D ) Strength - Resillience
7. Which of the following is false: a. The coefficient of thermal expansion is larger if the bond energy is smaller b. Ceramics are generally ionic bonding c. Van der Waals bonding is generally stronger than covalent bonding d. The free electrons in metallic bonding is reason for electrical conductivity 8. Which of the following is true: a. Polymers are generally denser than ceranmics b. Young's modulus of ceramics are similar to polymers c. Composites have higher tensile strength than metals d. Ceramics have low resistance to fracture than metals
What’s the correct answer please?
44
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
9.7 - Perform the following reclassification: Reclass by ID to assign Type- ID Туре f 4 d. 6 7 e 5. 3.
Data: Tensile Strength b (mm) L (mm) d (mm) P (N) Tensile Strength (MPa) Average (MPa) 49.74 52.14 10.14 760 49.74 52.14 10.14 980 51.18 49 8.74 800 48.56 48.86 10.96 960 49 51.54 9.72 780
1-5) The costs, C, to manufacture a part using either method A or method B are estimated by the following formulas CA = 32 + 0.85P CB = 74 + 0.9P – 0.010P², where the cost C is in dollars and P is the number of parts. (a) Estimate the breakeven point, ie the number of parts where the cost from either method is the same. (b) Which method would be less expensive to produce 100 parts?