A pipeline of 300mm diameter carrying water at an average velocity of 4.5 m/s branches into two pipes of 150mm and 200mm diameters as shown. If the average velocity in the 150mm pipe is 5/8 of the velocity in the main pipeline, determine the average velocity of flow in the 200mm pipe and the total flow rate in the system (Q). Q1, Vị = 5/8 V Di = 150 mm V = 4-5 m/s 300 mm Q, D2 = 200 mm

A pipeline of 300mm diameter carrying water at an average velocity of 4.5 m/s branches into two pipes of 150mm and 200mm diameters as shown. If the average velocity in the 150mm pipe is 5/8 of the velocity in the main pipeline, determine the average velocity of flow in the 200mm pipe and the total flow rate in the system (Q). Q1, Vị = 5/8 V Di = 150 mm V = 4-5 m/s 300 mm Q, D2 = 200 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An incompressible fluid flows steadily through two pipes of diameter 0.15 m and 0.2 m which combine to discharge in a pipe of 0.3 diameter. If the average velocities in the 0.15 m and 0.2 m diameter pipes are 2 m/s and 3 m/s respectively, then find the average velocity in the 0.3 m diameter pipe.
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1.25 km long and taken from a point distance of 1.5 km from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f = 0.0075, and neglect minor losses.
Water flows through a pipe AB of diameter d1= 60mm, which is in series with a pipe BC of diameter d2= 85mm in which the mean velocity V2 = 3m/s. At C the pipe forks and one branch CD is of diameter d3 such that the mean velocity V3 is 2.5 m/s. The other branch CE is of diameter d4= 40mm and conditions are such that the discharge Q2 from BC divides so that Q4= ½ Q3. Determine Q1, Q3, Q4 and d3.
prove that the flow is physically possible : v = Hzy
A water source generates a flow rate of 30 m 3/s in a region of y= 0 with angle zero degree and x=0 with an angle of 90 degree. Determine the magnitude of water velocity V at r= 5 m ( Use pi number =3 and water density =1000 kg/m3)ANSWER: V= 4 m/s
Air flows steadily through the variable area pipe shown with negligible viscous effects. Determine the flow rate in terms of h, D, d as shown in the diagram. Calculate the air flow rate in m^3/s if h = 0.1m, D = 0.3 m, and d = 0.15 m.
Water (ρ = 1000 kg/m3) is flowing vertically in the pipe shown below. The top, middle, and bottom parts have radii of r1 = 3 cm, r2 = 1 cm, and r3 = 3 cm, respectively. The speed of water flow and the gauge pressure at point 1 are v1 = 20 cm/s and P1 gauge = 200 Pa. The height difference between point 1 and 2, point 2 and 3 is 10 cm. Use g = 10 m/s2 for the acceleration due to gravity. What is the speed of the water flow at point 2? What is the gauge pressure at point 2? What is the speed of the water flow at point 3? What is the gauge pressure at point 3?
The water enters the system at A as shown in Figure Q2. Determine the average velocity of the water through section 2 pipe given that the average velocity of the water through section 1 is v₁ = 3 m/s. Q=3 m³/s A D2 = 80 mm 1 D₁ 150 mm B
The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. 0.409 MPa 0.125 MPa a. The energy added in meters and the power delivered in kilowatts to the water by the pump. b. The mechanical efficiency of the pump. P 0.04meter Ø 0.1meter Ø
Water flows into the pipe connection shown at '6' and '2' and leaves the system at '1'. It is not open to the atmosphere at any connection. The gauge pressure at both inlets is 12 psig and the velocity at both inlets is 9.5 ft/sec. Determine the horizontal force (lbf) needed to hold the fittings in place. 2 7.5" 1 2.5" 3 4 5 6 1.0"
+7