A pipeline is buried horizontally at a distance of 10 cm below the earth's surface. Where the soil having a thermal conductivity of 0.5 W/m.K. The pipe has an outer diameter of 100 mm with surface temperatures of 175°C. If the soil surface temperature is 20°C, estimate the heat transfer rate per unit length.

A pipeline is buried horizontally at a distance of 10 cm below the earth's surface. Where the soil having a thermal conductivity of 0.5 W/m.K. The pipe has an outer diameter of 100 mm with surface temperatures of 175°C. If the soil surface temperature is 20°C, estimate the heat transfer rate per unit length.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HEAT TRANSFER A thick-walled tube of stainless steel of 19 W/m°C with 2cm inner diameter (ID) and 4cm outer diameter (OD) iscovered with a 3 cm layer of asbestos insulation (k=0.2W/m°C) if the inside wall temperature of the pipe ismaintained at 600°C, calculate the heat loss per meter oflength, and the tube-insulation interface temperature.Stainless steel T1= 600 °C / Asbestos T2= 100 °C. SHOW COMPLETE SOLUTION IN A PAPER
A steel tube, with a thermal conductivity of 50 W /m K, has an inner diameter of 20-mm and outer diameter of 26-mm. Hot gases flow over the tube with a convection heat transfer coefficient of 200 W/m2 K; while, cold water flows through the tube with a convection heat transfer coefficient of 8000 W/m2 K. What is the hot-side overall heat transfer coefficient in W/m2 K?
Q2/ A hot surface at 100 C is to be cooled by attaching 27778 copper fins (k=237 w/m.K), 3 cm long for each fin, 0.25 cm dia. to it. Temp. of surrounding air is 30 C and h =35 w/m2.K on the surface. Calculate the heat rate from the surface for a 1m X 1m section of the plate. Also, determine the effectiveness of the fins.
I need help on 2b
A square pin fin (w=0.6 mm, L=33 mm) is attached to hot surface [87 mm * 69 mm] Ts= 172°C with convection heat transfer coefficient of (1383 W/m K) and surrounding air at 24°C, if the fin efficiency is 0.81 and the center to center distance between any two successive fins =1.5 mm. What is the heat transfer rate (W) from the base surface ONLY when the fins are attached to it?
A cylindrical shape body of length is 1.9 m and diameter is 400 mm is inside a room where the ambient temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 1.3 W/m^2.K. What is the thermal conductivity K.
Thermal jackets are typically put on cryogenicstorage tanks to minimize the heat transfer gainsfrom the surroundings. Consider a cylindercontainer that is 1.5 m long made from steel (k = 750W/m.K) with an inner diameter of 0.5 m and outerdiameter of 0.7 m. If the liquefied natural gas (LNG)inside the cylinder is maintained at 90 K, ambientconditions are Tamb = 20 °C, h = 7 W/m2.K. What isthe required thermal jacket thickness to maintainthe outer temperature of that jacket of 15 °C? (Takea thermal conductivity of the insulation to be kins =0.015 W/m.K). Image credit: Okorder. Image forillustrative purposes only.
Thermal jackets are typically put on cryogenicstorage tanks to minimize the heat transfer gainsfrom the surroundings. Consider a cylindercontainer that is 1.5 m long made from steel (k = 750W/m.K) with an inner diameter of 0.5 m and outerdiameter of 0.7 m. If the liquefied natural gas (LNG)inside the cylinder is maintained at 90 K, ambientconditions are Tamb = 20 °C, h = 7 W/m2.K. What is the required insulationmaterial to maintain the outer temperature of that jacket of 15 °C? Usethe end of the book and write your assumption with the right value.(Take a maximum allowed jacket thickness of Lins = 7 cm)
Plate glass 5 mm thick at 200°C is to be cooled from both sides using air at 40°C. If surface cracks are to be avoided, determine the maximum value of convective heat transfer coefficient. Material properties are density = 2500 kg/m3, specific heat 670 J/kgK. Thermal conductivity 0.744 W/mk. Also determine the time required in this to cool the plate to 80°C.