A pipeline having a diameter of 250 mm has a rate of flow of 0.30 m³/sec. from point 1 to 2, with 2 lower than 1. A gate valve is connected at a point 3 near point 2. The elevation of point 2 is 100 m. O Compute the elevation of 1 when the gate valve at 3 is closed and the difference in pressure P2 - P1 = 78 КРа. ® Compute the head loss from 1 to 2 when the gate valve at 3 is open and the difference in pressure Ри- Р2%3D 160 kРа. 3 Compute the length of pipe from 1 to 2 if f = 0.020.

A pipeline having a diameter of 250 mm has a rate of flow of 0.30 m³/sec. from point 1 to 2, with 2 lower than 1. A gate valve is connected at a point 3 near point 2. The elevation of point 2 is 100 m. O Compute the elevation of 1 when the gate valve at 3 is closed and the difference in pressure P2 - P1 = 78 КРа. ® Compute the head loss from 1 to 2 when the gate valve at 3 is open and the difference in pressure Ри- Р2%3D 160 kРа. 3 Compute the length of pipe from 1 to 2 if f = 0.020.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer it soon
Water flow at a 250mm diameter horizontal pipe 875m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 153.68 L/s В No answer among the choices C) Q = 101.07 L/s D) Q = 118.43 L/s E Q = 132.74 L/s F Q = 172.81 L/s %3D
The total discharge in the system below is 15.5 cfs and the head loss from B to C is 24 ft. Using n = 0.011 for all pipes, determine the following: a. head loss hl1 (ft) in pipe 1, and b. head loss his (ft) in pipe 5. 2000 ft 12 in 3000 ft 1500 ft 4000 ft 30 in 10 in 24 in А В D 2500 ft 4 15 in
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section? A. Section 1: 5.89 ft/sec Section 2: 9.2 ft/sec B. Section 1: 8.9 ft/sec Section 2: 6.0 ft/sec C. Section 1: 9.9 ft/sec Section 2: 9.9 ft/sec D. Section 1: 4.89 ft/sec Section 2: 6.58 ft/sec
8.7
Along a 50-m pipeline, there is a half-open globe valve (K = 10), four 90-degree smooth bends (K = 0.45), and six 45-degree elbows (K = 0.15). Ignoring the major head loss, what will be the pressure drop in this pipe if the flow velocity is 1 m/s? Fluid is water: Specific weight = 9810 N/m³. O 0 kPa O 6.35 kPa O 13.81 kPa O 21.67 kPa
Determine the flow (m³/s) in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 L/s.