Answered: A pipeline consists of three successive…

A pipeline consists of three successive lengths of 50cm, 40cm, and 30cm pipes. With a continous discharge of 300 liters/s of oil sg=0.75. Compute the mean velocity in each pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: design of pipeline 2-3 for water network shown in the figure below:- (90m) (83m) L=2000m Q=1.5 m3/…

Q: What is the flow speed of the system shown in the figure, if you want to drive in the lower limit of…

A: Given values: Reynold's no, R = 5000 f = 0.012 L = 50 m H = 20 m

Q: The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B C The end Cis an…

A: Option(2) is the correct answer

Q: Calculate the head loss in a circular concrete pipe flowing half filled.The diameter of the concrete…

A: diameter of concrete pipe = 1.5ft length = 1000/36 ft flow velocity = 150/36 ft/sec

Q: Calculate the velocity V m/s at a pipeline cross section where the total head, H is 54.6 m, the…

A: ###Determination of Velocity in Pipe at given Section of pipe #### Using bernoulli equation##

Q: 5. Determine the flowrates distribution in each pipe using Har B 2.5 m³/s i. ii. iii. 10 m³/s- A…

Q: A pipeline is to convey 0.6 m³/s of water between two reservoirs 8 km apart and 60 m different in…

A: Data given Discharge = 0.6 m3/s Total head difference = 60 m Length, L = 8 km = 8000 m Find:…

Q: A 25 cm diameter pipe carries oil of specific gravity 0.9 at a velocity of 3m/s. At another section…

Q: Assume a 30-cm diameter horizontal pipeline conveys water at a flowrate of 0.21 m³/s. The pressure…

A: The installation of small turbine with excess pressure with further pipeline is reduced to meet…

Q: Oil flows at the rate of 0.22 m³/s in a 500 mm diameter pipeline 500 m long. Specific gravity of oil…

Q: Question 5 a. In pipeline networks, state the condition that needs to be imposed on the flow rate…

A: (a)Given condition when pipe connected in (i)parallel(ii)series (b)Find discharge,Q?

Q: Which of the following statements about Energy Grade Line (EGL) and Hydraulic Grade Line (HGL) is…

A: different statements about energy grade line (EGL) and hydraulic grade line (HGL)need to find the…

Q: In the pipeline shown below, the following data are given: Coefficient of friction, f for all pipes:…

A: We knowhL=8fLQ2gD5π2we knowQ1=Q4=0.01m3s-1Q1=Q2+Q3hf=hf1+hf2+hf4hf2=hf3

Q: A pipe network consist of Pipeline from A to B, then at B, it is connected to pipelines 2 and 3,…

Q: use the three fundamental equations , to solve head losses numerical problems. A discharge of 750…

A: Q=750L/s D=400mm L=65m

Q: 4. A pipeline with diameter of 850 mm and length of 4.1 km connects two fresh water open reservoirs…

Q: Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be…

A: In hydraulic system minimum diameter of pipe is used so that high pressure can be maintained in…

Q: A municipal water supply diversion pipe carries flow from Lake Agnes to the watershed divide at…

A: Using the formula, Q = 0.432×C×(D^2.63)×(S^0.54) Where, C = Hazen Williams' constant (For High…

Q: en the pitot tube is moved vertically inside the pipeline, why does it yield different flow…

A: The instrument used for measuring the fluid flow velocity is known as pitot tube.

Q: he pump shown in the figure adds 15 ft of head to the water being pumped when the flow rate is 1.5…

A: Diameter of pipe, Length of pipe, Pressure at A,

Q: For the pipe network shown in figure 2, determine the corrected flow in pipeline CD and BC. For the…

A: Given: kAB=kCD=1kAC=kBD=2kBC=3 To find: Actual flow in CD and BC. Method used: Hardy cross method.

Q: for pipe flows for given pipe lengths (m) and pipe diameters (mm). Initial flow as shown in the…

A: First, separate the Loops like 1 and 2 then find the iteration with two different loops Find the…

Q: How do I calculate the friction heads, indicated with the RED ARROW

A: Given data, Diameter D = 300 mm Length L = 5 km Roughness factor = 0.03

Q: A 250 waste water pipe is installed on a slope of 0.010 mm/mm and has a roughness n = 0.013.…

A: Hence Velocity (V) = 1.222 m/s Depth of flow = y= 0.125 mExplanation: Step 2: Step 3: Step 4:

Q: The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzle having a…

A: The given figure is shown below:

Q: 1.78 67 2.67 ies in a system having a static l inor loss coefficient of 20. Dete

A: two siphons are in seriestotal head H =80 ft length L=1200 ftdiameter =6 inches =612 ft' =0.5 ft f…

Q: This question needs to be solved correctly otherwise rating will be given negative. 25-cm in…

A: Given - Diameter of Pipe (D) = 25 cm Relative Roughness = 0.01 Total Length of Pipe (L) = 50…

Q: Figure 2 shows a reticulation system. Estimate the flow rate in each pipeline using Hardy-Cross…

A: pipelength L (m)diameter D (m)AB9000.25BC7500.2CD9500.25DA7500.2

Q: Consider the gravity pipeline shown below figure, which transmits a discharge of 0.3 m3/s. Determine…

A: Given, Head difference= 120-110 =10 m C=100 Q=0.3 m3/s L=500 m

Q: A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of…

A: Given Flow discharge (Q)= 4.6 cfs Diameter at section 1 (D1)=12''=1ft Diameter at section 2…

Q: Calculate the head loss of a pipeline with a discharge of 2100 m3/hr flowing through a pipe 450mm in…

Q: Oil having a kinematic viscosity of 6.8 x 10-6 m2 /s flows through a pipeline with a discharge rate…

Q: Given the properties of the pipelines, together with the elevation of water in the three-reservoirs,…

Q: For the conditions given below, find the mass flowrate (lbm/sec). Density (p) is 62.4 lbm/ft³ 1. The…

A: Diameter of pipe (d) = 18 inch = 1.5 ftLength of flow (L) = 300 ftHazin william coefficient (C) =…

Q: Use the Hazen-Williams Equation to calculate the flow rate of water in a 4.5-km long, 4-m diameter…

A: Given: The length of the pipe is 4.5 km. The diameter of the pipe is 4 m. The head loss is 30 m.

Q: In a laminar flow through a circular pipeline of 20 cm diameter, the flow velocity at a hadial…

Q: A pipeline with a diameter of 0.9 m divides into three 0.45 m pipes at elevation 120 m. Each of the…

A: D1=D2=D3=0.05mf=0.017

Q: Fluid Flow in Pipes A 4km long pipeline, 88 cm in diameter connects two fresh water open reservoirs…

Question

A pipeline consists of three successive lengths of 50cm, 40cm, and 30cm pipes. With a continous discharge of 300 liters/s of oil sg=0.75. Compute the mean velocity in each pipe.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the pipeline sytem shown below determine a) DBC if LBC = "100*k" m b) LBC if DBC = 15 cm AB BC AC A L (m) 100k ? 200k D (cm) 5 2.5 ? B 5 Q (l/s) 7 ? 10 k = 84 C f 0,02 0,02 0,02
a pipeline of 600mm diameter is 1,5km long. to increase the discharge another line of the same diameter is introduced parrallel to the fisrt in the second half of the length . if f = 0,01 and head at the inlet is 300mm, calculate the increase in discharge. neglect minor losses
Find the headloss (ft) in a pipeline consisting 98ft. Of 2.9 inches in diameter. The flowrate is 1.6 ft^3/s kerosene. Use manning’s formula,n=0.014 Express in whole number
Oil of specific gravity 0.802 and kinematic viscosity 0.000186 m /s flows from tank A to tank B through 305 m of new pipe at the rate of 0.089 m3/s. The available head is 0.161 m. What size pipe should be used?
From the given three reservoirs shown. The elevation A is 346 m., B is at elevation 301 m and C is at elevation 241 m. Rate of flow at 1 is 200 liters/sec. PIPE LENGTH (M) DIAMETER HAZENS, C (MM) 450 600 120 3600 300 100 3 1200 D3 110 Determine the diameter of pipeline 3. 175 mm 177 mm O 180 mmm O 184 mm None of the above
Determine the theoretical diameter of a single 1-mi-long pipeline from A to C that would be equivalent to the pipe system shown in Figure 7-31 A. 0.5 mile 16 in. B 0.8 mile 12 in. 0.7 mile 8 in. C
With a flow of 86.4 cu. m. per sec., determine the approximate diameter size of a pipe in mm considering the allowable head loss of 20 m per 1000 m and the following: a) f-value of 0.018, b) C-value of 80, and c) n-value of 0.015.
q5 (b) The discharge and velocity of flow over the model of a spillway are 4 m3/s and 3.2 m/s, respectively. Determine the velocity and discharge over the prototype, which is 25 times the size of the model. Refer to Table 5(b).
QUESTION 5 Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m³/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7
A 250 mm cast iron pipe 600 m long carries a discharge of 250 liters/sec. between the two reservoirs A and B with A higher than B. If the flow rate is doubled by replacing the existing pipeline of the same diameter, what length of pipe should be used? Assume f = 0.02.
3. **A 32800 ft long pipeline, of commercial steel with the nominal diameter of 12 inch of schedule number 40, conveys water from a reservoir (top water level 2790 ft above the sea level) to a water treatment plant (2230 ft above the sea level). Assuming that the reservoir remains full, and neglecting minor losses, estimate the volume flow rate. Take the viscosity µ = 1.00 CP.
The two lines shown are the EGL and HGL of a pipeline. Which statement is true? * (1 Point) A B The diameter of pipes in AB and BC are the same There is no velocity at end C O The slope of EGL in BC denotes head loss