a pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos ( K= 0.396(btu-in)/(hr-ft-F) followed by a layer of cork 1.5 inches thick ( K= 0.30 (btu-in)/ft (hr-ft-F). if the temperature of the outer surface of the cork and pipe is 90 F and 290 F RESPECTIVELY, calculate the heat loss per 100 ft of insulated pipe in btu/hr

a pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos ( K= 0.396(btu-in)/(hr-ft-F) followed by a layer of cork 1.5 inches thick ( K= 0.30 (btu-in)/ft (hr-ft-F). if the temperature of the outer surface of the cork and pipe is 90 F and 290 F RESPECTIVELY, calculate the heat loss per 100 ft of insulated pipe in btu/hr

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please include a fbd of the problem
Determine the thermal conductivity of water vapor at 174°C.
Calculate the heat loss through a 100-ft² wall with an inside temperature of 65°F and an outside temperature of 35°F. Assume the exterior wall is composed of 2- in. of material having a 'k' factor of 0.80, and 2-in. of insulation having a conductance of 0.16. RTotal = 8.75 & Q = 342-Btu/hr RTotal = 9.2 & Q = 399-Btu/hr RTotal = 8.75 & Q = 399-Btu/hr RTotal = 9.2 & Q = 342-Btu/hr Hide hint for Question 3 Utilize the (RTotal = 1/C + x1/k1) equation.
Express final answers in foursignificant figures.
A furnace wall is to be designed to transmit a maximum heat flux of 220 Btu/hr.ft of wall area. The inside and outside wall temperatures are to be 2200 • F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with ak of 0.44 Btu/hr. ft. ° F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. ° F and a maximum usable temperature of 2400 ° F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in.-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. F)|
The thermal conductivities of human tissues vary greatly. “Fat” and “skin” have conductivities of approximately 0.200 W /m 0K and 0.0200 W /m 0K, respectively, while other “tissues” inside the body have conductivities of approximately 0.500 W /m 0 Assume that between the core region of the body and the skin surface lies a “skin” layer of 1.00mm, a “fat” layer of 0.500 cm., and 3.20 cm. layer of other “tissues”. A)Find the R-factor for each of these three layers, and the R-factor for all layers taken together
Hint: You found out where is the maximum temperature.
Determine the resistance (in F-h/BTU) of a hollow cylinder with an inside and outside radius of 2 in and 2.1 in, respectively. The length of the cylinder is 6 ft while the thermal conductivity is 22 BTU/hr-ft-F
Determine the thermal conductivity of water vapor at 174°C.
If a heat transfer coefficient of 2.84 W l(m2 • K) exists on each of the two inside faces of two sheets of 6.35-mm-thick glass separated by an air gap, calculate the gap that can be used such that the rate of heat transfer by conduction through the air gap equals the rate of heat transfer by convection. What is the rate of heat transfer if this gap is exceeded. The thermal conductivity of air of 0.0242 WI (m . K). Solve for temperature of 20°C and 12°C on the outside surfaces of the glass. Would the calculated gap change in value for different values of the surface temperatures? Would there be any advantage to increasing the gap beyond this calculated value?