A pin-connected truss composed of members AB and BC is subjected to a vertical force P= 40 kN at joint B (see figure). Each member is of constant cross- sectional area: AAB =0.004 m2 and ABC = 0.002 m². The diameter d of all pins is 20 mm, clevis thickness t is 10 mm, and the thickness t of the bracket is 15 mm. Determine the normal stress acting in each member and the shearing and bearing stresses at joint C. Fc Clevised ends A 1.5 m P=40 kN 2.

A pin-connected truss composed of members AB and BC is subjected to a vertical force P= 40 kN at joint B (see figure). Each member is of constant cross- sectional area: AAB =0.004 m2 and ABC = 0.002 m². The diameter d of all pins is 20 mm, clevis thickness t is 10 mm, and the thickness t of the bracket is 15 mm. Determine the normal stress acting in each member and the shearing and bearing stresses at joint C. Fc Clevised ends A 1.5 m P=40 kN 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q70: For the truss shown in the Figure, if the diameter of pins at A and E are 60mm and 80mm, respectively. The stress in A is double shear while it is single shear in E. Determine the shear 3m 2m 2m 3 m 3 m 3 m F 3 m 110KN 110 KN stresses in pins at A and E and the stresses in members BG; and member BC if their diameter is 110 mm.
An axial pull is acting on a bar consisting of two different materials is shown in figure.If the Young’s Modulus of M.S steel and Copper is 2 x 105 N/mm2 and 121 GPa respectively. Determine (i) Stress induced in each section, and; (ii) Total extension of the bar
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 4,500 lbs and the cross sectional area of the rod is 0.85 in?, determine the stress in each section. Steel Bronze 4P Aluminum P 2 ft 3 ft 2.5 ft
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 390 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 180 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a P i Answer: Pmax B b KN
A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 3.00 in. and a wall thickness of 0.210 in. Determine the normal stress in truss member BC. Assume P = 4 kips, Q = 2 kips, a = 5 ft, b = 9 ft, and c = 7 ft. The stresses are positive if tensile and negative if compressive. Answer in ksi rounded-off to 2 decimal places. P e (3) B b T Gra a Adc Ref you
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 590 mm, b = 295 mm, h = 360 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a ● b
A uniform concrete slab of total weight W is to be attached, as shown in the figure, to two rods whose lower ends are on the same level. Determine the ratio of the areas of the rods so that the slab will remain level. Figure P-215 Steel E - 29 x 10 psi Aluminum E - 10 x 10 psi L- 4 ft L-6R Total Weight = w 3 ft 6 ft The value of the load P at the aluminum 0.33 W b. 0.67 W с. W d. none of the above The ratio between the internal reactions of the aluminum and the steel 2.03 b. 0.49 c. 0.67 d. none of the above The ratio between area of steel and area of the aluminun 0.867 b. 0.409 c. 0.258 d. none of these If the value of W is limited to 1500 lb, which of the statements is true? The maximum load the steel can carry is greater than of the aluminum The maximum load the aluminum can carry is greater than of the stell The sum of loads at the steel and the aluminum is twice the value of steel The deformation developed at the steel is greater than that of aluminum If the cross-sectional area…
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 920 mm2. Assume a = 2.4 m, b = 9.0 m, and c = 4.1 m. If P = 60 kN and Q = 75 kN, determine the normal stress in each member. P y L₂ C MPa (C) Answers: OAB = a b