A piece of engineering equipment is supported by the foundation shown. The diameter of the circular pin is 20 mm. 50 2 S0 100 S0 12 a.) Determine the value of P so as not to exceed the allowable bearing stress of 310.5 Mpa in the circular pin. b.) Determine the value of P so as not to exceed the allowable shearing stress of 138 Mpa in the circular pin.
Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.
A: Maximum axial force P that can be applied to the steel plate
Q: 3.00m long steel wire is fixed in a ceiling and a mass of 12.3kg is hanging from the wire. The wire…
A:
Q: A child slides across a floor in a pair of rubber-soled shoes. The frictional force acting on each…
A: NOTE: As per bartleby guidelines we can answer only first question. For remaining questions please…
Q: The material for the 58-mm-long specimen has the stress–strain diagram shown. A) If P = 150 kN is…
A:
Q: Two strips of metal are pinned together as shown with a rod 10 mm diameter. The ultimate shear…
A: Given: Diameter=10mm Therefore, =5mm Shear stress=60Mpa.
Q: P k a P te
A: Shear stress; is a force that tends to cause material deformation by slippage along a plane or…
Q: 5. (a) Explain the differences in edge and screw dislocations. (b) Locate your screw dislocation at…
A: A) Edge and screw dislocations are two types of crystal lattice defects that can occur in materials.…
Q: A hollow shaft with an outside diameter of D=54 mm and an inside diameter of d = 40 mm is subjected…
A: To determine the shear stress on the element, we can use the torsion equation: τR=TJhere,τ=The shear…
Q: A beam having the cross section shown is subjected to a vertical shear V. NOTE: This is a multi-part…
A: Consider the distance y from the bottom end where the shear stress is maximum. As shown in the…
Q: QUESTION 16 The T-beam is made of a nylon. The allowable stress is 24 MPa in tension and 30 MPa in…
A: The area of the top section will be, A1=80×30 ⇒A1=2400 mm2 And the area of the bottom section will…
Q: The bonded single lap joint shown below has a width, w = 97 mm and an overlap length, I = 28 mm. =…
A: Given that: Overlap length I = 28 mm Thickness h = 1.1 mmwidth w=97 mmTensile load F=4385 NShear…
Q: Assume if the shear stress in steel exceeds about 4.00 x 108 N/m2 the steel ruptures. (a) Determine…
A:
Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…
A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…
Q: Two wooden members of 70 x 110-mm uniform rectangular cross section are joined by the simple glued…
A: Given: ϕ=20°, L=110mm, B=70mm, τ=500kPa The uniform rectangular cross-sectional area of the wood is…
Q: Problem 3: The rectangular bars shows are in tension and are joined together by two bolts as shown.…
A: Given rectangular bars having joined by two bolts given the bolts have diameter d of 38inch and…
Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…
A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…
Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…
A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…
Q: Two solid cylindrical rods support a load of P = 37 kN as shown in Figure below. R has a diameter of…
A: We know that we first draw a free body diagram of the system given as Now We calculate the angle…
Q: For the given state of stress, determine: (1) The principle stresses and the directions of the…
A: Solution:- 1). In the figure given we have: σx= 350…
Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…
A: Stress is defined as force per unit area. σ=FA Where F is a force and A is cross-section area.
Q: maximum shear = 60 MPa and modulus of rigidity = 77 GPa. Basing from the angle of twist determine…
A:
Q: Assume if the shear stress in steel exceeds about 4.00 x10 N/m2 the steel ruptures. (a) Determine…
A:
Q: P-1. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…
A: Given data d=90 mmT=10 kN-mG=200 GPa Here, d is the diameter and T is the torque. While G is the…
Q: he support consists of a solid red brass C83400 copper post surrounded by a 304 ainless steel tube.…
A: Given, A figure with dimensions. We need to calculate, the greatest axial load that can be…
Q: Mechanical stress is Select one: O a. a change in the relative position of the points of the body,…
A: Mechanical stress is defined as force per unit area , when a load is applied to the material .…
Q: 20. Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm.…
A:
Q: A horizontal force of P = 36 kN is applied to joint C. Each pin has a diameter of 25 mm and is…
A:
Q: The 530-lblb load is applied along the centroidal axis of the member. (Figure 1) PART A) Determine…
A: Given:-
Q: P4. If the cross section of the femur at section a-a can be approximated as a hollow as shown,…
A: Maximum normal stress = 235.98 lb/in2 = 236 psi Detailed solution is given below: Please UPVOTE sir
Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…
A:
Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…
A: Given: Length of each beam, L=4 m Area of cross-section,A=7.5×10-3 m2 Load, W=4.5×104 N Young's…
Q: 2. A tubular aluminium bar of a square cross section with outside dimensions of 50 mm x 30 mm,…
A: Given that Torque,T=300 Nm shear stress,S=20 MPa=20×106 Pa Allowable rate of twist,θ=0.025 rad/m…
Q: Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What…
A: Given, Diameter of the metal bar, d = 6.0 mm = 6.0 × 10–3 mRadius, r = d/2 = 2.5 × 10-3 m Maximum…
Q: A wire of length “Lo” and cross-sectional area S supports a weight W vertically. a) This fine wire…
A: Given dataA wire of length Locross-sectional area Sa weight W vertically. Step 1:From Hooke's Law,…
Q: coefficient of viscosity is equal to the ratio of shear stress to shear strain. True or False? a)…
A: True or False: Coefficient of viscosity is equal to the ratio of shear stress to shear strain.
Q: 2. Three steel bolts are to be used to attach the steel plate shown to a wooden beam. Knowing that…
A: Load, Ultimate Shearing Stress, Factor of Safety, F.S = 3.25
Q: The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine…
A: Given: Here are the given data, Brass, d=6.5 inches Copper, d=4.5 inches Fbr=450 lbFco=250 lb To…
Q: Block A is held in equilibrium when force F = 140 lbf is applied. Each cable is made out of 5-0s…
A:
Q: The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial…
A: Solid circular rod cross-sectional area = 410 mm2.Uniform axial distributed load( w) = 10 kN/m.Two…
Q: 2. A Torque of magnitude T = 900 N.m is applied at D as shown. Knowing that the diameter of shaft AB…
A:
Q: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800 N while…
A:
Step by step
Solved in 3 steps with 1 images