• A piece of chromium steel of length 7.4cm (density= 8780kg/m³, k=50 W/m K) and specific heat capacity (C,=440 J/kg K) with mass 1.27 kg is rolled into a solid cylinder and heated to a temperature of 600 °C and quenched in oil at 36 °C. Show that the lumped capacitance system analysis is applicable and find the temperature of the cylinder after 4min. What is the total heat transfer during this period? You may take the convective heat transfer coefficient between the oil and cylinder at 280 W/m2K.

• A piece of chromium steel of length 7.4cm (density= 8780kg/m³, k=50 W/m K) and specific heat capacity (C,=440 J/kg K) with mass 1.27 kg is rolled into a solid cylinder and heated to a temperature of 600 °C and quenched in oil at 36 °C. Show that the lumped capacitance system analysis is applicable and find the temperature of the cylinder after 4min. What is the total heat transfer during this period? You may take the convective heat transfer coefficient between the oil and cylinder at 280 W/m2K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the Poisson equations? How would the respective equations look like at isothermal, iso-choric, isobaric conditions?
A metallic ball of radius ro = 5 mm, is initially in equilibrium at 400 C in a furnace. It is suddenly dropped to water at 20 C (hw =last 5 digits of your student number W/m K, e.g your student number is 201912345 then hw = 12345). The properties of the sphere are density= 3000 kg/m", k = 20 W/m_ K, c = 1000 J/kg K, and a= 6.66E-6 m/s. Calculate the time required for the center of the sphere to cool to 50 C. %3D 2
Find the steady-state temperature distribution in a (very long) solid cylinder if the boundary temperatures are T(s=0, θ, z)=0 and T(s, θ, z=0)=s*sinθ
* Energy Equation : (First law of thermodynamics) + (8-1). M? du u dT T =。
Consider the osmotic pressure-mediated nuclear compression under various concentrations of polyethylene glycol (PEG). What would the bulk modulus be if a nucleus with volume 1500 µm3 was reduced to 1000 µm3 with a 10% PEG solution?
I need the answer as soon as possible
(a) A length of brass piping is 30 m long at a temperature of 18°C. When hot water flows through it the temperature of the pipe rises to 70°C. Determine the length of the hot pipe if the coefficient of linear expansion for brass is 18 x 10-6 K-¹.
Suppose that a rod of length 150 cm is immersed in steam untill it's temperature is uo =2720c.At time t = 0,its lateral surface is insulated and its two ends are imbedded in ice at 0°C.Calculate the rod's temperature at at point on the rod at a distance x-95cm after 32 seconds ,for thermal diffisuvity K3D0.005.
In some cases, the coefficient of linear expansion varies with temperature, showthat in that situation ? = [1 + ∫ ?(?)?? ??0]. Note: Q.2 also shown in the image.
An insulated vertical cylindrical vessel of cross- sectional area A = 0.12 m² contains 20 mol of He gas at To = 300 K and Po= 0.5 bar. It is capped by a movable piston of mass m = 150 kg supported from the ceiling by a wire. The top of the vessel is open to the atmosphere (Patm= 1 bar, Tatm= 300K). The wire is cut and the weight falls and com- presses the gas. Patm 160 E Wir og SLOWA He gas 1019 (a) Obtain the pressure and temperature of the gas a short time after the wire has been cut, when a negligible amount of heat transfer has taken place. Comment on whether your solution takes into account the inevitable oscillations of the piston around its equilibrium position before it comes to rest. mut Ispl (b) After a long time, the He gas thermally equilibrates with the environ- ment by heat transfer through the piston. How much heat is exchanged with the environment during this process? Helium can be considered an ideal gas at all conditions of interest, with C₁=3R/2. INST
Needle ball bearings, D=5-mm, H=26-mm, are heated up to 1200 K in a heat treatment furnace where the micro-structure is transformed from pearlite to austenite. As soon as taken out of the furnace, they are quenched in water having T=286 K and h=174 W/m2K to transform the micro- structure from austenite to martensite. Find the time required for cooling the bearings to T=326 K. Assume the bearings are perfectly cylindrical and made of AISI 347 Steel. H
rド-1 rf-1 Lk(rc-1)] 1 1. Derive the formula of thermal efficiency e =