A short bronze cylinder of diameter 6 cm and length 12 cm is initially at 40°C and then plunged into a fluid at 200°C. The temperature at the centre of the cylinder is measured by a thermocouple to be 150°C after 5 minutes. What is the convective heat transfer coefficient between the cylinder and the fluid? The following properties of the bronze cylinder may be used: Thermal conductivity k = 26 W/m-K, density p = 8800 kg/m³, and specific heat c 420 J/kg-K. State and justify all assumptions made.

A short bronze cylinder of diameter 6 cm and length 12 cm is initially at 40°C and then plunged into a fluid at 200°C. The temperature at the centre of the cylinder is measured by a thermocouple to be 150°C after 5 minutes. What is the convective heat transfer coefficient between the cylinder and the fluid? The following properties of the bronze cylinder may be used: Thermal conductivity k = 26 W/m-K, density p = 8800 kg/m³, and specific heat c 420 J/kg-K. State and justify all assumptions made.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.10P: 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the...

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate of dimensions 2.00 cm × 2.00 cm x 0.40 cm. One end of a thermally insulated copper wire (diameter D = 2.70 mm and length L = 12.0 cm) is dipped into a vat of liquid nitrogen (T = 77.2 K), and the other end is attached to the bottom of the silver plate. (a) If the silver plate starts at room temperature (73.0°F), what is the initial rate of heat flow between the plate and the liquid nitrogen reservoir? (b) Assuming the rate of heat flow calculated in part (a), estimate the temperature of the silver plate after 30.0 seconds.
Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate of dimensions 2.00 cm × 2.00 cm × 0.60 cm. One end of a thermally insulated copper wire (diameter D = 2.70 mm and length L = 18.0 cm) is dipped into a vat of liquid nitrogen (T = 77.2 K), and the other end is attached to the bottom of the silver plate.(a) If the silver plate starts at room temperature (65.0 °F), what is the initial rate of heat flow between the plate and the liquid nitrogen reservoir?(b) Assuming the rate of heat flow calculated in part (a), estimate the temperature of the silver plate after 30.0 seconds.
Heat Transfer with a Liquid Metal. The liquid metal bismuth at a flow rate of 2.00 kg/s enters a tube having an inside diameter of 35 mm at 425°C and is heated to 430°C in the tube. The tube wall is maintained at a temperature of 25°C above the liquid bulk temperature. Calculate the tube length required. The physical properties are as follows (H1): k = 15.6 W/m K, c,=149 J/kg K, u = 1.34 x 10-3 Pa s.
Need help I'm not sure where I went wrong on this
What’s the correct answer for this please ?
An ordinary egg can be approximated as a 5.5-cm-diameter sphere whose thermal conductivity of roughly k = 0.6- W mk overall density of p = 1000; and heat capacity of C₂ = 3000- kg m² The egg is initially at a uniform temperature of T₂ = 10°C and is dropped into boiling water at T.. = 90°C W - determine how long it will take for the egg to m²K Taking the convective heat transfer coefficient to be h reach T = 70°C. In solving the problem, please follow the steps below. For the Lump Model In solving this problem, please use the lump model method (ignoring the requirement of small Biot number and discuss the outcomes, 1. 2. Compute the characteristic length Lc Compute the volume and surface area of the sphere (as the egg model) Vol As 3. Compute the diffusivity α = = 10- k p Cp = J kgk Compute non-dimensional excessive temperature 0 = h Lc k 4. Compute the Biot number using the characteristic length found above Bi = T-Too 5. Ti-Too 6. Calculate the Fourier number from the equation =…
please show full and detailed solution.
Example: 0.5 kg of water per minute is heated from 20° to 40°C when passed through a tube of 2.5 cm diameter steel pipe. The pipe surface temperature is maintained at 110°C by condensing steam on its surface. Find out the length of the pipe required. The properties of water at mean temperature of 70°C are given below: p = 978 kg/m² k= 0.575 W/m. K Cp = 4200 J/kg. K v = 0.415 x 10-6 m²/sec
The physics of the convection heat transfer of thermosses phenomenon and the mathematical model should be discussed.
Conduction 1. A thermodynamic analysis of a proposed Brayton cycle gas turbine yields P= 5 MW of net power production. The compressor, at an average temperature of T. = 400°C, is driven by the turbine at an average temperature of T₁ = 1000°C by way of an L = 1m-long, d= 70mm - diameter shaft of thermal conductivity k = 40 W/m K. Compressor min T Combustion chamber Shaft L Turbine Th out (a) Compare the steady-state conduction rate through the shaft connecting the hot turbine to the warm compressor to the net power predicted by the thermodynamics- based analysis. (b) A research team proposes to scale down the gas turbine of part (a), keeping all dimensions in the same proportions. The team assumes that the same hot and cold temperatures exist as in part (a) and that the net power output of the gas turbine is proportional to the overall volume of the device. Plot the ratio of the conduction through the shaft to the net power output of the turbine over the range 0.005 m s Ls 1 m. Is a…