A piece of Aluminium of cross sectional area 60 mm is bonded to a piece of steel of cross sectional area 120 mm. The lengths of both materiais are the same at 150 mm. The component is then heated through a temperature rise of 100 °C. Take Es = 207 GN/m2 and EAL = 45 GN/m? as = 12 x 10° °C and aAL = 27 x 10 PC. (a) Find the stresses induced in the steel and aluminium. b) Find the extension of the compound bar. %3D

A piece of Aluminium of cross sectional area 60 mm is bonded to a piece of steel of cross sectional area 120 mm. The lengths of both materiais are the same at 150 mm. The component is then heated through a temperature rise of 100 °C. Take Es = 207 GN/m2 and EAL = 45 GN/m? as = 12 x 10° °C and aAL = 27 x 10 PC. (a) Find the stresses induced in the steel and aluminium. b) Find the extension of the compound bar. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(c) An element is subject to the stresses shown below in Figure 5 Calculate the centre and radius of the Mohr's stress circle and sketch the circle (1) (ii) Calculate the values of principal stresses and show them on the circle (ii) Determine the direction of the larger principal stress relative to the 75 N/mm. 30 N/mm A 14 Nmm 75 N/mm2 30 N/mm Figure 5
A thin plate of linear elastic materials (E = 200 GPa, 0.25) is in plane stress (a, = Txz = Tyz = 0). The plate is heated by 100 °F and the thermal V = expansion efficient of the plate is, a = 8 x 10 6. °F The plate is also compressed between two rigid, perfectly smooth surfaces as shown in the figure. 50 MPa 150 MPa Find the following: a. The non-zero stress in the plate. b. The change in the dimension in X- direction. c. The strain in the thickness direction of the 400 mm plate, ɛ, and change in the thickness of the plate f the initial thickness is 4 mm. 200 mm
The subject is Mechanics of Deformable Bodies
A steel rod 10 mm in diameter and Im long is heated from 20°C to 120°C, E = 200 GPa and a = 12 × 106 per °C. If the rod is not free to expand, the thermal stress developed is: (a) 120 MPa (tensile) (c) 120 MPa (compressive) (b) 240 MPa (tensile) (d) 240 MPa (compressive)
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] pipe is subjected to a tensile load P. The pipe has an outside diameter of D = 280 mm, a cross-sectional area of A = 7550 mm², and a length of L = 9.5 m. The initial longitudinal normal strain in the pipe is zero. After load P is applied and the temperature of the pipe has been increased by AT = 40°C, the longitudinal normal strain in the pipe is found to be 2260 με. Calculate the magnitude of load P. Answer: P = M. L kN D P
The subject is Mechanics of Deformable Bodies
I need the answer as soon as possible
We have a grounded 2 cm in diameter steel shaft which is 10 cm in length connected to a rigid surface. This shaft is subject to the stresses at the tip point as given below; • Tmean = 100 Nm, Talternating= 50 Nm, • Mmean = 30 Nm, Malternating= 40 Nm, Fmean = 4 kN, Falternating = 6 kN. This shaft has minimum properties of Sy = 800 Mpa and Sut = 1000 Mpa. Assume; Kf for bending=D1.5, Kf for tension = 1.4, and Kfs for torsion = 1.8. Using Modified Goodman criterion what can you say about the shaft? a) Does it have an infinite life?
Two forces are applied to a flywheel 50 cm in diameter. Each force is 500 N. The shaft is fixed to the wall using three grade 5 steel bolts. The distance between the bolts and the axis of rotation is 10 cm. (a) What moment of resistance must develop the three bolts together Answer: 250 Nm (b) What is the resistance force F of each bolt? Answer: 833.3 N (c) What is the diameter of the bolts if their factor of safety is 10? Answer: 4.14mm
A bar of 12 mm diameter gets stretched by 3mm under a steady load of 8000 N. What stress would be produced in the bar by a weight of 800 N which falls through 8 cm before commencing the stretching of the bar which is initially unstressed. Take E= 2 × 105 N/mm2
Machine design please try to explain with some word
The tensile load on a rod stretched between two fixed points is 4500 N. The temperature is 25°C. The cross sectional area of the rod is 170 mm2. Determine the stress that will be experienced by the rod at -10°C. The linear expansion coefficient is 11.7 x 106 mm/mm-°C and the modulus of elasticity is 200 GPa. Express your answer in MPa.