A person's toe displacement is measured by video analysis during running. The raw coordinates are contaminated by pure 50 Hz noise with an amplitude of ±1 mm. The raw data is not filtered prior to the calculation of acceleration. What will the magnitude of the noise component within the acceleration signal be? a. ± 1 mm b. ± 50 mm O c. ± 250 mm O d. ± 2500 mm

A person's toe displacement is measured by video analysis during running. The raw coordinates are contaminated by pure 50 Hz noise with an amplitude of ±1 mm. The raw data is not filtered prior to the calculation of acceleration. What will the magnitude of the noise component within the acceleration signal be? a. ± 1 mm b. ± 50 mm O c. ± 250 mm O d. ± 2500 mm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In Chopper operation I0 is positive , the direction of power flow will be from ......... to .........
A shunt generator on dest is separately encited and driven at 1000 rev /min. The open circuit test chars. are given Field test CA o 0'157 O.477 0 663 O.805 1.0 129 Induced Emf CU) 12a5 300 400 100 450 500 550 ine mlc is then shunt Connected and gun at l000 revlmine with a constant field cicuit esistance of 540R. The agmature docuit resistamee is er. Deduce and plot the load Chargaetesistics of this mle,negleeting effeetof amarterre reaction.what is value of manimum lbud cursrent.
The OCC is measured by increasing the fieldcurrent in steps from zero to some maximum value, and recording the corresponding values of armature emf. If now the current is decreased from maximum to zero, the emf values will be different; why?
For a dc machine, its commutator has a diameter of 50 c rotating at 1000 rpm. For a brush width of 1 cm, the time commutation taken by the machine will be _________a) 0.382 msb) 0.456 msc) 0.573 msd) 0.312 ms
Q7/ A separately excited DC motor has the following parameters: Ra = 0.3 2, Ke = 0.52 V/rpm.Wb, d (flux per pole) = 150 mWb. The motor speed is controlled by a full wave bridge 'rectifier. The firing angle a is set at 30°, and the average speed is 1500 rpm. The applied a.c. voltage to the bridge is 440 V at 60 Hz. Assuming the motor current is continuous; calculate the armature current drawn by the motor and the steady-state torque for the cases of: (a) half-wave converter (b) Fully- controlled bridge
Q9) Estimate the positon of the pointer in PMMC instrument if damping torque is absent? a. Pointer moves to full scale deflection b. Pointer does not come to rest position c. Pointer does not stop at the value of measurement d. Pointer does not move from zero
Quest 2. (a) Explain the following types of noise: ) thermal noise (1) transit time notse
1d-1f answered please.
Q#3. Discuss the operating principle of wind turbine? In what manners the frequency and amplitude of a generator output varies with wind speed? What measures should be taken to control it? Solution#3 (to be typed here by the student)
Obtain the analysis (state table and state diagram) of the synchronous sequential circuit in the figure below. What structure does the circuit have from Moore and Mealy type machines?
) A chopper circuit drives an inductive load from 120 DC supply. Given the load resistance as 6 0, the average load current as 52.5 A and operating frequency is 450 Hz. When the chopper is ON, 5 V is dropped. Calculate of (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (1. (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform tic (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in four quadrant operation (RL load) and explain its operation. ( Duty Cycle ON period OFF period
22 A pressure measurement system is specified as having a non-linearity error of 10.5% of the full-scale reading, a hysteresis error of ±0.5% of the full-scale reading and a repeatability error of ±0.4% of the full-scale reading. What is (a) the overall worst possible error, (b) the overall most likely error? ( 14.