A person is pushing two boxes placed side by side with each other. What is the acceleration caused by the applied force if the net force is 107.33 N, the coefficient of kinetic friction of the boxes is 0.043 and the sum of the mass of the boxes is 91.5 kg?  Is it possible to have one of the boxes generate an applied force of 123.16 N, if yes, what is the mass of the other box?

Q: A 3 kg box is sliding across a frictionless table at a rate of 5 m/s. It encounters a 35° incline…

A:

Q: consider a circle of radius 1m and weight of 100n resting on a right angle surface where the…

A:

Q: at which the 40 ° slope can be climbed with a 60 kW power? d) What is the power required to climb a…

A:

Q: A small object of mass m is located on the surface of the disk with radius R if the magnitude of the…

A: We will answer the first question since the exact one was not specified. Please resubmit the…

Q: A 10 lb block slides 6 ft down a plane inclined 40 degrees with horizontal. Determine the work done…

A:

Q: While the astronauts are trying to fix the crane, the cable slips off the pulley and the buggy falls…

A: Once applied, force is described as an external cause that alters or tends to modify the…

Q: Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 80…

A:

Q: fully loaded elevator cabin has a mass of 1200kg. In 3.0 minutes, the cabin must be raised to a…

A: Given,  Elevator's counter mass, mc=950 kg Elevator cab mass, me=1200 kg Distance, d=54m Time…

Q: A person pushes horizontally with a force of 150 N on a 69.0 kg crate to move it across a level…

A: Given:find:a) The magnitude of the frictional forceb) The magnitude of the crate acceleration

Q: A 10-kg crate, starting from rest, is pulled across a floor with a constant horizontal force of…

A:

Q: A 10 kg block is moving on a horizontal table. The coefficient of kinetic friction between them is…

A: Given: Mass of block is 10 kg. The coefficient of kinetic friction is 0.3.

Q: A 35-kg child rides on a 10-kg bicycle with 500-mmdiameter wheels. Determine the horizontal force…

A: In this problem, the rolling resistance will be the necessary horizontal force to push the child and…

Q: The mass of blocks A and B shown in the figure below are mA = 5 kg and mB = 35 kg, successively. The…

A: given  mass of the block A, ma=5kgmass of the block B, mb=35kgcoefficient of friction between blocks…

Q: In the given figure below, a 3.0 -kg block is sliding down a 60o-rough incline. The speed of the…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: A light spring with force constant 3.80 N/m is compressed by 7.60 cm as it is held between a…

A: Write down the given value using suitable variables. Here K signifies force constant, x signifies…

Q: The tensions of a flat belt are;tight side 500N and slack side 180N.the angular speed N and diameter…

A: Given data: T1=500 NT2=180 NN=280 rpmD=20 cmm=1.2 kg/mμ=0.6 Need to determine the  initial tension…

Q: EXAMPLES. (1) A box weighing 100 lb is pushed 20 ft along a level floor at constant velocity by a…

A:

Q: A 20 kg box on a horizontal table is pushed by a horizontal force of 30 N as shown on the right. If…

A: Given data: The mass of the box is M = 20 kg. The coefficient of friction between the box and the…

Q: For Belt Friction, why it's possible to increase the tension in one side while maintaining the…

A: Given: There are friction in a belt which can be wrapped around a pulley or wheel. And due to the…

Q: Calculate the total power needed from the motor to drive an electrical conveyor belt, which carries…

A: The total power needed from the motor to drive an electrical conveyor is 10.8137 kW.

Q: Determine the horizontal force required to move a 2500-lb automobile with 23-in.-diameter tires…

A: Given Weight of the automobile = 2500 lb Diameter of the tyre = 23 in Coefficient of rolling…

Q: ted on anoti nean radius i mer, then en

A:

Q: Friction force between a block and horizontal plane depends upon the coefficient of friction between…

A: Yes, the friction force between a block and horizontal plane depends upon the coefficient of…

Q: What average force is necessary to bring a 45.0-kg sled from rest to a speed of 3.00 m/s in a period…

A: First we calculated the value of acceleration using equation of motion and then put values in, Force…

Q: A 1.21 kilogram block is released from rest on a 13.33° frictionless incline. The object proceeds…

A: To find: The kinetic friction on the horizontal surfaces. Given: The mass of the block is m=1.21 kg.…

Q: A  truck weighing 5 kips is traveling with a constant velocity of 50 mph when brakes are applied…

A:

Q: A 46.5-kg box is being pushed a distance of 7.16 macross the floor by a force P whose magnitude is…

A:

Q: image

A: Given: Mass of the blocks is 20 kg. Coefficient of friction for the inclined block is 0.28. Angle of…

Q: kg, al ed together, compressing a spring S bet- =t on a level, frictionless surface. The sp to…

A: Given data as per question Mass of block A, mA=1 kg Mass of block, B, mB=3 kg Speed of block B,…

Q: How much breaking speed does the cable car need to descend at a constant speed? One day the brakes…

A:

Q: with each oth C tal frictionless SS

A:

Q: What is its position and velocity at t= 9.2 s? What is the new velocity and new position?

A:

Q: Consider the following arrangement of masses: Mass 1 is connected to mass 2 by a very light string…

A: Given: m1=15 kgm2=15 kgkinetic friction, μk=0.73initial speed, v=1 m/s

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.