A Pelton turbine with a 1.75 m impeller radius has a nozzle with a mouth diameter of 12 cm. Since the optimum rotational speed of the impeller is n=250 rpm to generate maximum power from this Pelton turbine, which is used to generate hydroelectric power; (The rotation angle of the turbine blades is given a p=165°) a) Find the velocity of the water jet. b) Calculate the volumetric flow rate of the flow throu 91,63 m/s 95,71 m/s 1,457 2,012 82,37 m/s 102,78 m/s 1,225 1,036 85,68 m/s 0,851

A Pelton turbine with a 1.75 m impeller radius has a nozzle with a mouth diameter of 12 cm. Since the optimum rotational speed of the impeller is n=250 rpm to generate maximum power from this Pelton turbine, which is used to generate hydroelectric power; (The rotation angle of the turbine blades is given a p=165°) a) Find the velocity of the water jet. b) Calculate the volumetric flow rate of the flow throu 91,63 m/s 95,71 m/s 1,457 2,012 82,37 m/s 102,78 m/s 1,225 1,036 85,68 m/s 0,851

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
I need the answer as soon as possible
A fluid with a density of 0.8 g/cm3 is being emptied from a very large tank through a small cylindrical opening with a diameter d. Use the figure below to calculate a) the diameter d_of the opening if the mass flow rate at point 2 is 1.45 kg/s, and b) the flow velocity at point 3. 1. H = 4 m d = ? 3 h = 1 m 2.
2) A 180° elbow forces the flow to make a U-turn and discharges it to the atmosphere at a mass flow rate of 40 kg/s. The diameter of the entire pipe is 10 cm. Calculate (a) the velocity of water in the pipe (b) the gauge pressure inside the pipe (c) the anchoring force needed to hold this pipe in place 180° L. Water 40 kg/s FRE FRX 50 cm 9)
In our house water pipe line with diameter of 2cm is connected to shower head that has 35 holes. The speed of the water in the pipe line is 1.1m/sec. i) What is the volume flow rate in the pipe line? ii) At what speed does the water leave one of the holes with diameter 0.0014m in the shower head?
A pump delivers 2000kg/min of water (50°C) from reservoir A (El. 10m) to reservoir B (El. 40m). The suction line is 300mmx180m and the discharge line is 250mmx 50m. The pipes are made of wrought iron and the cavitation parameter as 0.2. Neglecting minor losses, find the reading of the pressure gage in mm Hg at the pump suction.
Please don't copy from other site.
This is thermodynamics subject. I need complete solution (step by step process) with given. Thanks
3.4 Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree
Three immiscible fluiids are contained in a tank: 1.0 m of water, 1.20 m of oil (s= 0.80) and air under a pressure of 16 kPa. The tank is closed and has a height of 3.0 m and diameter of 1.0 m. Find the theoretical velocity throught a 5 cm diameter orifice located 30 cm above the bottom of the tank.CHOICES: a.10.34 m/s b.15.8 m/s c.12.56 m/s d.8.03 m/s
This is Thermodynamics subject. Complete solution with GIVEN pleaseee. Thanks a lot.