A part of a 50 Hz power transmission and distribution system is represented by Figure Q3a. The system operates with a power factor close to 1.0. i) ii) iii) 245 kV CB1 xh Fault Location A: IFA = 60 KA 2.65Ω 200 MVA X = 10% CB2 Figure Q3a 0.2 Ω 33 kV Estimate the fault current at location B. Fault Location B The rated MVA of the transformer is taken as the base MVA for the per unit system. Define and calculate the base voltage, base impedance and base current on both sides of the transformer. Calculate, with details, the per unit value of the total impedance from the 245 kV generator to Location B in Figure Q3a.

A part of a 50 Hz power transmission and distribution system is represented by Figure Q3a. The system operates with a power factor close to 1.0. i) ii) iii) 245 kV CB1 xh Fault Location A: IFA = 60 KA 2.65Ω 200 MVA X = 10% CB2 Figure Q3a 0.2 Ω 33 kV Estimate the fault current at location B. Fault Location B The rated MVA of the transformer is taken as the base MVA for the per unit system. Define and calculate the base voltage, base impedance and base current on both sides of the transformer. Calculate, with details, the per unit value of the total impedance from the 245 kV generator to Location B in Figure Q3a.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3-phase side. The main transformer primary to secondary turns ratio is (12/1).
In no load phasor diagram of practical transformer, the magnetizing current Imag is with flux Ø O Leading by 30° O Lagging by 60° In phase O 90° out of phase
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
A single-phase 730 V/ 1824 V, 56 Hz transformer has a maximum core flux density of 1 Tesla and an effective core cross- sectional area of 61 cm2 Determine the number of secondary turns. O 2137 O 1203 O 1203 O 48
In part c determine the voltage across Rp and Xp .
SOLVE STEP BY STEP IN DIGITAL FORMAT
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
1. How to create a magnetic field with the use of electricity? 2. Why an Alternating Current can only be used in transformers? 3. How basic transformer works/principles ? 4. Compare and Contrast: Step-Up and Step-down transformers solve all or will dislike answer Solve all Parts
The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation Full-load copper loss Load power factor 0.5 Lagging 5% The Maximum noccihle voltage regulation of the trane former is: 5.033 96 5.385 9 3 96 4.134 % 21 21
Topic- basic & const.