A parallel flow between two large isothermal plates with one plate moving at a constant velocity of 10 m/s and the other stationary. Consider such a flow with a uniform spacing of 10 mm between the plates. The temperatures of the upper and lower plates are 50° C and 10° C, respectively. By simplifying and solving the continuity, momentum, and energy equations, determine the velocity and temperature distributions and heat fluxes at the plate (Fluid properties: k = 0.145 W/m-K, µu = 0.605 N-s/m² ). %3D

A parallel flow between two large isothermal plates with one plate moving at a constant velocity of 10 m/s and the other stationary. Consider such a flow with a uniform spacing of 10 mm between the plates. The temperatures of the upper and lower plates are 50° C and 10° C, respectively. By simplifying and solving the continuity, momentum, and energy equations, determine the velocity and temperature distributions and heat fluxes at the plate (Fluid properties: k = 0.145 W/m-K, µu = 0.605 N-s/m² ). %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A liquid is entering a 10 m long pipe of 0.2 m diameter at 25°C with an average velocity of 0.02 m/s. The pipe is kept at a constant surface temperature of 40°C. Assume the flow is both hydrodynamically and thermally fully-developed in the pipe. Find out the outlet temperature. Justify if the assumption of fully-developed flow is appropriate. The properties of the fluid can be assumed constant with following values Density: 484.2 kg/m³; Specific heat capacity: 2802 J/kg.K; Thermal conductivity: 0.0904 W/m.K; Dynamic viscosity: 9.197 × 10-5 kg/m.s; Prandtl number: 2.85. 29.3 °C
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Water at 45° C flows over a large plate at a velocity of 25 cm/s. The plate is 1.2 m long in the flow direction, and its surface is maintained at a uniform temperature of 10° C. Calculate the steady rate of heat transfer per unit width of the plate.
Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 3.30 m/s. Surface temperature of the 1.800-m long flat plate is constant at 50°C. The properties of engine oil at Tf = (150°C + 50°C)/2 = 100°C are k = 0.1367 W/m∙K, v = 2.046 × 10−5 m2/s, Pr = 279.1. Determine the local convection heat transfer coefficient at 0.200 m from the leading edge and the average convection heat transfer coefficient. The local convection heat transfer coefficient at 0.200 m from the leading edge is ___ W/m2·K. The average convection heat transfer coefficient is ___ W/m2·K.
Oilflow in a journal bearing can be treated as parallel flow betweentwo large isothermal plates with one plate moving at a constant velocityof 12 m/s and the other stationary. Consider such a flow with a uniformspacing of 0.7 mm between the plates. The temperature of the upperand lower plates are 47°C and 17°C, respectively. By simplifying andsolving the continuity, momentum, and energy equations, determine:(a) thevelocity andtemperature distributionsin the oil.(b ) the maximum temperature and where itoccurs.(The location ofmaximum temperature is determined bysetting dT/dy=0).(c) the heat flux from the oil to each plate
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.
Water flows through a tube of 5mm inside diameter with a volumetric flow rate of 7.8 cm3/s. Wall temperature of the tube is kept constant at 80oC. In a fully developed velocity and temperature profile region of 5m length, calculate the bulk temperature of exiting water if its inlet temperature is 20oC
Air at 10°C and 1 atm is flowing parallel at a velocity of 15.5 m/s over the top flat surface of copper plate. The top surface of the copper plate is 0.03m by 0.03m square. The temperature of copper plate is uniform at 65.6°C. For laminar flow, calculate the dimensionless Reymolds number (Nre) and Nussel number (NNu). Table A.3-3a. Physical Properties of Air at 101.325 kPa (1 Atm Abs), SI Units Bx (Bp²/1?) T (kJ/kg · u x T (Pa ·s, k (W/m 103 (1/K • (°C) T (K) (kg/m³) K) -17.8255.41.379 1.0048 1.62 × 6s or kg/m · s) · K) Npr (1/K) m³) 0.022500.7203.92 2.79 x 108 O 273.21.293 1.0048 1.72 × (0-5 0.024230.7153.65 2.04 × 108 10.0 283.21.246 1.0048 1.78 ×/0 0.024920.7133.53 1.72 x 108 37.8 311.01.137 1.0048 1.90%/0-S 0.027000.7053.22 1.12 x 108 Select one: O A. NRe = 27826.58; NNu =98.58 O B. NRe = 23215.74; NNu =152.68 O C. NRe = 27826.58; NNu = 152.68 O D. NRe = 23215.74; NNu =98.58
Exhaust gases at 1 atm and 300°C are used to preheat water in an industrial facility by passing them over a bank of tubes through which water is flowing at a rate of 6 kg/s. The mean tube wall temperature is 80°C. Exhaust gases approach the tube bank in normal direction at 4.5 m/s. The outer diameter of the tubes is 0.035 m, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 0.09 m. There are 16 rows in the flow direction with eight tubes in each row. Assume the air properties at 250°C and 1 atm. The air properties at the assumed mean temperature of 250°C and 1 atm are k = 0.04104 W/m·K ρ = 0.6746 kg/m3cp =1.033 kJ/kg·K Pr = 0.6946μ = 2.76 × 10−5 kg/m·s Prs = Pr@Ts = 80°C = 0.7154 The density of air at the inlet temperature of 300°C (for use in the mass flow rate calculation at the inlet) is ρi = 0.6158 kg/m3. The specific heat of water at 80°C is 4.197 kJ/kg·°C. Determine pressure…
6- Air at a pressure of 200 kPa and free-stream temperature of 27°C flows over a square flat plate at a velocity of 30 m/s. The Reynolds number is 10° at the edge of the plate. Calculate the heat transfer for an isothermal plate maintained at 57 C. v = 8,6x10 k = 0.0274; Pr = 0.7 V Nu = 1299 Answers: g = 676W
2. Consider laminar fully-developed flow through two smooth isothermal tubes. One tube has circular cross-section the other has square cross-section. The cross-sectional area is the same for both tubes. Show that the convection coefficient in these two flows are related as hcircular 1.088hsquare- %3D Assume that the fluid properties are the same.
Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a velocity of 5 m/s in an 8-cm-diameter and 10-m-long tube when the tube is subjected to uniform heat flux from all surfaces. Use fluid properties at 25° C and assume fully developed turbulent flow in the entire duct.