A number of different adhesive joint geometries are shown below. Which ONE of the following lists is CORRECT in ordering them in terms of decreasing strength? Simple lap Tapered lap Scarf Butt Double strap Tapered double strap Double lap Strap Stepped lap a) Double strap > Tapered double strap > Double lap b) Scarf > Tapered lap > Tapered double Lap c) Double lap > Simple lap > Butt d) Scarf > Butt > Simple lap e) Scarf > Tapered double strap > Double strap

A number of different adhesive joint geometries are shown below. Which ONE of the following lists is CORRECT in ordering them in terms of decreasing strength? Simple lap Tapered lap Scarf Butt Double strap Tapered double strap Double lap Strap Stepped lap a) Double strap > Tapered double strap > Double lap b) Scarf > Tapered lap > Tapered double Lap c) Double lap > Simple lap > Butt d) Scarf > Butt > Simple lap e) Scarf > Tapered double strap > Double strap

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is 2736 sq.mm, allowable shear Fv is 150MPa, Allowable tensile stress Ft = 0.6Fy with Fy = 250 MPa. Questions: a) Design force P b) Total required length of weld using 12 mm fillet weld c) Value of “b”
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
A 76 x 76 x 6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy=248MPA and Fu =400MPA. Gusset Plate Allowable Stresses: Allowable tensile stress (gross area) = 0.60FY Allowable tensile stress (net area) = 0.50F. Allowable shear stress (net area) = 0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85%.
Compute the available block shear strength of the gusset plate and design tension strength. 2 in A- B- D 3 in El F. 2 in 0.375 in 0.375 in 2 in 3 in 3 in 2 in (not to scale) Section properties Material properties plate width = 7 in ASTM A36 steel plates plate thickness =/s in F, = 36 ksi %3D standard hole size F,= 58 ksi
Please answer the problem attached image. Thank you very much. Using NSCP 2015
Differentiate how to test welded from tension joints.
Hand written please
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
| * A's O As,web As bw Steel areas: A's-2 + 14 = 308 mm² A₁=50 mm² (area of $8) Materials : C25/30 / B420C Longitudinal reinforcements A's=2 $ 14 As,web= 2 $ 12 As= 5 0 14 bw=300 mm d=670 mm d'=30 mm k₁= 0,85 k3 = 0,85 Pb=0.0205 (from table) Transverse Reinforcements $8/200 mm (2-leg stirrups) Material coefficients Ymc:1.5 (Concrete) Yms: 1,15 (Steel) Determine the reinforcement ratio and failure type of the beam As,web= 212= 226 mm² Asw=2x50=100 mm² (Total Area of two leg stirrup) A₁= 5 + 14=770 mm²
Please explain all Via handwritten, Specifically DF makes little confusion.
A:17 docs.google.com a 35 MPa 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/.. find the bearing stress between bolts and plate
Based on block shear strength of the double angle.