A nozzle is formed so that its cross sectional area converges linearly along its length. the inside diameters are 200mm and 100 mm at inlet and exit and the length of the nozzle is 1m. What is the convective acceleration at a section halfway along the length of the nozzle if the discharge is constant at 0.12 ?3/s.

Q: h D ↑ Bernoulli Equation: Water flows from a reservoir down a circular pipe of diameter D = 1 cm at…

A:

Q: he water tank in the figure is being filled through section O t vi = 4 m/s and through section 3 at…

A:

Q: The velocity components for idealised flow along a right angled wall is given by u = 4 x m/s, v = -4…

A:

Q: Water flows around the vertical two-dimensional bend with circular streamlines and constant velocity…

A: Given data: v=10 m/sp1=62 kpa

Q: The velocity components for idealised flow along a right angled wall is given by u = 4 x m/s, v = -4…

A:

Q: e vorticity

A: ZERO VORTICITY

Q: The stream function for a two-dimensional flow is Y = (0.5x² -y²) m²/s where x and y are in meters.…

A:

Q: The choked nozzle that converges and diverges. Find the nozzle areas ratio that divides by the…

A:

Q: A 200 kg chunk of lead falls from a height of 30 m and smashes into a rigid concrete floor.…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: 3 6 The scenario: SAE 30 oil running through a 50 cm new steel sheet metal pipe 50 meters long has…

A: SAE 30 oilDiameter of new steel sheet metal pipe, D = 50 cm = 0.5 mLength of cast iron pipe, L = 50…

Q: 2. An incompressible fluid flows past a stationary flat plate with uniform inlet profile and a…

A: Plate width = bControl volume height = Control Volume width = WInlet velocity = v0Outlet velocity,

Q: a) Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in the…

A:

Q: An incompressible frictionless flow field is given by V = (Ax + By)i + (Bx – Ay)j where A = 1 si and…

A: The term "velocity field" refers to the dispersion of velocity in a flow zone. It is written as…

Q: 5. Water flows around a vertical circular bend between radii Ry and R2 with speed profile given by V…

A: given data

Q: Consider the stea dy flow of a fluid through a duct. The fluid density at t to the duct is 1000 kg/m…

A: Given Data→ Type of flow - Steady Fluid flow Fluid density at the entrance to the duct ρ=1000kgm3…

Q: For fully-developed laminar flow through a pipe with ra- dius R, the fluid velocity is very…

A:

Q: Determine the y component for steady state and incompressible fl

A: For solution refer below images.

Q: Euler's approximation and (b) Lagrangian approximation. Discuss the acceleration for the particle…

A: For solution refer below Images.

Q: For the velocity profile shown find  1.The total displacement ,D(in): 2.The average speed,S(in/s):

A:

Q: A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times…

A:

Q: Determine whether of the following flows are irrotational, and find the velocity potential function,…

A:

Q: Water is flowing in a circular pipe of varying cross-sectional area. At one point in the pipe the…

A:

Q: A viscous laminar fluid between two parallel plates is driven by the top plate moving at a constant…

A:

Q: The horizontal V fitting, steady, uniform flow at each section, incompressible, and neglect weight…

A: Let us find the velocities at 1 and 2 - Q=A1V1 =A2V20.4=π4201002V1=π481002V2V1=12.73ms, V2=79.577ms…

Q: h 1 2 4.0 cm 1.0 mm 3

A: height of nozzle from top free surface of waterh=27cm=0.27mdiameter of nozzled=1mm=1×10-3m

Q: In the Fig Shown, the Flow rate Pipe (A) is equal ( GA=25 Lit15), the diameter is equal ( DA - 75…

A:

Q: If pipe 1 has volumetric flowrate of 0.004 m^3/s, and pipe 2 Q2= 5.6549 L/s, and pipe 3 diameter 70…

A: Here, given data Q1=0.004 m3/sQ2=5.6549 lit/s     =0.0056549 m3/sd3=70 mm Now, consider flow…

Q: The net pressure force along the horizontal direction (N). Net out flow rate of momentum through the…

A: As per honor code and answering guidelines I can answer 1st, 3 sub parts at time .If you want other…

Q: The cross-sectional area is 25 square centimeter of water jet under the velocity of 35 meter per…

A:

Q: Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure…

A:

Q: A steady flow of room temperature

A:

Q: A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil…

A:

Q: 3. Consider the one-dimensional, incompressible flow through the circular channel shown. The…

A: Given:Velocity at section 1:U(t)=U0 ​+U1 ​sinwtU0=20 m/sU1 =2 m2/sw=0.3 rad/sL=1 mR1= 0.4 mR2= 0.2…

Q: A pipeline of constant diameter 0.6m, with its centreline on a horizontal plane turnsthrough a…

A: The objective of the question is to calculate the horizontal components of force exerted on the pipe…

Q: A two-dimensional flow (x-y plane) is given by u =x +yt and v = - y+xt where u and y are the…

A: To Find : a) This flow incompressible.b) The time rate of change of u an v for the fluid…

Q: Water falls down a vertical pipe by gravity alone. The flow between vertical locations z1 and z2 is…

A: The modified pressure is : P'=P+hρg here. The pressure P is atmospheric pressure. P'=Patm+hρg for.…

Q: The velocity monitoring of a fluid is u = 48xy v = N. (48 + x2 + y2) Find the current function. Is…

A: Given: u = 48*xy v= N[48 + x2+y2 ] Let the current or stream function be psi We have  u =…

Q: Shown below is a fluid flowing throug converging-diverging nozzle. In an ac flow situation, what…

A: solution: From 1 to 2 in the flow direction, the given passage is a converging diverging section.