A non-rigid steel pipe 70 cm in diameter is to carry a maximum of 2,830Pa and additional pressure due to water hammer when quick closing valve stops a flow of 0.73 cubic meter per second. The pipe has a thickness of 22 mm and of Ew = 3000 MPa, Ep = 200000 MPa for steel. Compute the actual closure in the pipe after closure in Pa %3D

A non-rigid steel pipe 70 cm in diameter is to carry a maximum of 2,830Pa and additional pressure due to water hammer when quick closing valve stops a flow of 0.73 cubic meter per second. The pipe has a thickness of 22 mm and of Ew = 3000 MPa, Ep = 200000 MPa for steel. Compute the actual closure in the pipe after closure in Pa %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls answer, I'll rate. Determine the force in member BD in kN.If the force is compression, enter the answer as negative.Show your complete solution. Thank you so much!
The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel in kips. The holes each have a diameter of 5 inches. The unit weight of concrete is 144 lb/ft³. 10 in. | -12 in 12 in 12 in 12 in 12 in 12 in. 12 ft
Dont round off in solution, only round off in final answer in 2 decimal places. Answer asap
2. Determine the force member CJ. 3.10 m D → 3.5 kN E 3.72 m F 3.72 m В JI 3.72 m A H K 6.2 m 6.2 m Paint X lite
(47 H.WOA vod Con sists of three bars of unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rocd ? use E = 200G Va %3D Ø=4omm =30mm =20 mm 2.1W 60 1.5m 2.5m 2m
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE WEIGHT OF THE WIRE, DTERMINE THE REQURIED 500 Ib DIAMATER IF THE STRESS IS NOT TO EXCEED 20 ksi AND THE TOTAL ELONGATION IS NOT TO EXCEED 0.20 in. ASSUME E = 29 x 106 psi.
Please include FBD
SOLVE 9.3
Problem 2 The steel water pipe has an inner radius of 6 in and wall thickness 0.25 in. (1) If the valve A is open and the flowing water is under a gauge pressure of 240 psi. Determine the longitudinal and hoop stress developed in the all of the pipe. (2) If the valve A is closed. Determine the longitudinal and hoop stress developed in the all of the pipe.
Determine the losses in the post-tensioned concrete beam as shown below. 560 mm Given: POST-TENSIONED BEAM with A PARABOLIC TENDON PROFILE Span Length = 20 m fi = 1200 N/mm² A, = 2850 mm² Ac 4.23x105 mm² 1=9.36x10¹0 mm e-560 mm (@midspan, from N.A.) fc= 40 N/mm² Es = 210,000 N/mm² μ = 0.19 K = 0.0005 (per meter) Anchorage slip = 5 mm (jacked at left-end only). (make sure to draw the force variation diagram for anchorage slip) V/S= 6 RH = 70 Dead Load 9.97 kN/m fpy = 1714 N/mm² Bridge Width III
Determine the magnitude of the reaction at A and B dur to hydrostatic pressure?