A multi-layered wall with the dimensions shown in the figure has temperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials A and C are k-60 W/m-K, k 24 W/m-K. If total rate of heat transfer through the wall is 175 W, what is the thermal conductivity of material B? T- 200°C soc 6 cm 2 cm 25 om 4 cm

A multi-layered wall with the dimensions shown in the figure has temperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials A and C are k-60 W/m-K, k 24 W/m-K. If total rate of heat transfer through the wall is 175 W, what is the thermal conductivity of material B? T- 200°C soc 6 cm 2 cm 25 om 4 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Temperature distribution of a wall is given as T(x) = -100x + 50 and the cold surface is exposed to a convection environment at temperature of 20 °C. If the wall thickness is 10 cm and the conductivity is 1 W/mK what is the convection coefficient between the cold surface and the environment?
In a composite slab, the temperature at the interface (Tinter ) between two materials is equal to the average of the temperature at the two ends. Assuming steady one dimensional heat conduction, which of the following statements is true about the respective thermal conductivities?
one piece DU - Moodle English (en) - ESLIon -t yet swered The temperature distribution through a furnace wall consisting of firebrick and high-temperature block insulation and steel plate is measured as shown in the figure below. The thermal conductivity of fire brick is 1.13 W/(m. K). Find the heat loss per unit area of the furnace wall. rked out of 2 3 4 5 Flag question 760°C 758°C Block insulation 727°C | Outside air Hot gasef 68.42°C 26.5°C 68.5°C 6.35cm 12.7cm 0.635cm Select one: O a. 5.50 W/m2 O b. 550 W/m? O c. 55.0 W/m2 O d. 40 W/m2 Fire bri ck Steel casting
I need the answer quickly
Please solve quickly
Shown in the figure below is an insulated copper block that receives energy at a rate of 200 W from an embedded resistor. The temperature of the resistor is 34°C above the temperature of the copper block. Insulation Δt = Resistor 5000000000000000000000 oooooooooooooo....... Copper block If the block has a volume of 10-3 m³ and an initial temperature of 20°C, how long would it take, in minutes, for the temperature to reach 88°C? -V=10-³ m³ T₁ = 20°C min
A wall, as shown in figure, consists of four layers, with thermal conductivities, kį = 0.060 W/m.K, k3 = 0.040 W/m.K, and ka = 0.12 W/m.K (k) is not known). The layer thicknesses are L1 = 1.5 cm, L3 = 2.8 cm, and L4 = 3.5 cm (L2 is not known). The known temperatures are T1 = 50°C, T12 = 35°C and T4 = -10°C. Energy transfer through the wall is steady. Apply the concept of steady- state heat transfer through conduction on the wall, and determine the interface temperature T34? ki ks T T4 T12 T23 L L3
A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Calculate the heat loss per unit length of the pipe. Given the thermal conductivity of calcium silicate insulation equals to 0.09 W/m.K.
Consider the 2D heat conduction problem for a plane fin in the figure. Non-dimensionalize the problem in the figure.