A model for the control arm ABCD for the suspension of one of the wheels of an automobile is shown. The control arm is supported by ball-and-socket joints at points A and C, and by a spring BE. Points A, C, and Elie in the yz plane and are attached to the frame of the automobile. The vertical force P = 3 kN is due to the weight of the automobile, and the control arm has negligible weight. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 390 mm E 240 mm B (180, 120, 30) mm D (300, 120, 10) mm 70 mm Determine the force in spring BE. (Round the final answer to four decimal places.) (Do not include a minus sign in your response.) The spring force is kN compression.

A model for the control arm ABCD for the suspension of one of the wheels of an automobile is shown. The control arm is supported by ball-and-socket joints at points A and C, and by a spring BE. Points A, C, and Elie in the yz plane and are attached to the frame of the automobile. The vertical force P = 3 kN is due to the weight of the automobile, and the control arm has negligible weight. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 390 mm E 240 mm B (180, 120, 30) mm D (300, 120, 10) mm 70 mm Determine the force in spring BE. (Round the final answer to four decimal places.) (Do not include a minus sign in your response.) The spring force is kN compression.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 24P: When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of...

See similar textbooks

Similar questions

A person is lying on a board, which is supported at both ends. A vertical reaction force VA is acting on the board at point A and passes through the origin of the coordinate system. A vertical reaction force VB is acting at the point located at īB weight of the person is F and the weight of the board is P. The vector that determines the centroid C of the person is given by: xC 3.3 lex, where l is a length. It is known that the - aëx + Bēy. Determine the reaction forces VA and VB as a function of l, a, B, F and P. ex VB VA P ta
Asap plzzzzz
For the stepladder shown in the figure, sides AC and CE are each 3.31 m long and hinged at C. Bar BD is a tie-rod 0.819 m long, halfway up. A man weighing 948 N climbs 2.48 m along the ladder. Assuming that the floor is frictionless and neglecting the mass of the ladder, fınd (a) the tension in the tie-rod and the magnitudes of the forces on the ladder from the floor at (b) A and (c) E. (Hint: Isolate parts of the ladder in applying the equilibrium conditions.) B E (a) Number i Units (b) Number i Units (c) Number i Units >
SHOW WORK!!
The arm in the figure below weighs 35.1 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force F, in the deltoid muscle and the force F, exerted by the shoulder on the humerus (upper- arm bone) to hold the arm in the position shown. (Enter your answers to at least the nearest newton.) Ft Fs F, J12° F, 0.080 m 0.290 m
The asymmetrical support arrangement is chosen for a pedestrian bridge because conditions at the right end Fdo not permit a support tower and anchorages. During a test, the tensions in cables 2, 3, and 4 are all adjusted to the same value T. If the moment at Ois to be zero, what should be the value T, of the tension in cable 1? Determine the corresponding value of the compression force P (enter a positive number) at O resulting from the four tensions applied at A. Neglect the weight of the tower. -23'--33' 40' 40 50 B D. 15
A horizontal wire holds a solid uniform ball of mass (m) in place on a tilted ramp that rises 35.0° above the horizontal. ihe Surface of this ramp is perfectly smooth, and the wire is directed anay from the cen ter of the ball. (3.) What is the tension in the nire? 35.0°
The weightless strut in the figure below is not attached to the wall; it is prevented from falling only by friction. (Let w = 395 N, L = 5.15 m and h = 3.10 m.) (a) Find the magnitude of the force of friction between the wall and the strut.(b) Find the normal force exerted by the wall on the strut.(c) Find the minimum coefficient of static friction.
Don’t use a calculator to solve and show all steps
A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. What is the tension in the cable?
One end of a uniform meter stick is placed against a vertical wall. The other end is held by a lightweight cord that makes an angle ? with the stick. The coefficient of static friction between the end of the meter stick and the wall is 0.400. A block of the same weight as the meter stick is suspended from the stick, as shown, at a distance ? from the wall. Assume that theta= 15.0o in this problem. What is the minimum value of ? for which the stick will remain in equilibrium?
A gymnast rises onto her toes, as shown in the picture on the right. The floor pushes up on the ball of her foot with a force of N=313 N. If 0=56.0°, what are FH the forces in her heel (TH) and ankle joint (T), and what is the angle o? Answers: TH=481 N; T,=761 N; b=20.7° N, 0. 4.25 cm 9.66 cm 5.