A mixing beater consists of three thin rods, each 10.9 cm long. The rods diverge from a central hub, separated from each other by 120°, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has a cross-sectional area of 3.70 cm² and is so shaped that it has a drag coefficient of 0.500. The drag force on each ball is \( R = \frac{1}{2} D \rho A v^2 \) where \( D \) is the drag coefficient, \( \rho \) the density of the fluid, \( A \) the cross-sectional area, and \( v \) the speed of the object moving through the fluid.(a) Calculate the power input required to spin the beater at 1000 rev/min in water.\[ \text{______ W} \](b) The beater is taken out of the water and held in air. If the input power remains the same (it wouldn't, but if it did), what would be the new rotation speed?\[ \text{______ rev/min} \]

the drag force can be expressed as, R=12DρAv2=12DρArω2 1 v=rω the…

A mixing beater consists of three thin rods, each 10.9 cm long. The rods diverge from a central hub, separated from each other by 120°, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has cross-sectional area 3.70 cm? and is so shaped that it has a drag coefficient of 0.500. The drag force on each ball is R = 1 DpA v2 where D is the drag coefficient, p the density of the fluid, A the cross-sectional area, and v the speed of the object moving through the fluid. (a) Calculate the power input required to spin the beater at 1000 rev/min in water. (b) The beater is taken out of the water and held in air. If the input power remains the same (it wouldn't, but if it did), what would be the new rotation speed? rev/min

A mixing beater consists of three thin rods, each 10.9 cm long. The rods diverge from a central hub, separated from each other by 120°, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has cross-sectional area 3.70 cm? and is so shaped that it has a drag coefficient of 0.500. The drag force on each ball is R = 1 DpA v2 where D is the drag coefficient, p the density of the fluid, A the cross-sectional area, and v the speed of the object moving through the fluid. (a) Calculate the power input required to spin the beater at 1000 rev/min in water. (b) The beater is taken out of the water and held in air. If the input power remains the same (it wouldn't, but if it did), what would be the new rotation speed? rev/min

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Vlad needs to draw water from a deep well. He is using a bucket that is connected by rope (negligible mass) to a wooden axle at the top of the well. By cranking a handle at the end of the axle, Vlad is able to unwind the rope around the axle and move the bucket downward. The radius of the axle is R = 30 cm. The bucket is traveling downward at speed vi = 25 cm/s when the handle slips out of Vlad’s hand. As the rope unwinds and the bucket falls downward, the axle spins freely with an angular acceleration whose magnitude is α = 4.5 rad/s^2. The bucket falls through a distance of d = 7.0 m before crashing into the water. 1. What is the angular speed ωf of the axle when the bucket first hits the water? 2. As d → 0, what limit does ωf approach and why?
The wheels,axle, and handles of a wheelbarrow weigh W=56N. The load chamber and it’s contents weigh WL=635N.the drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward.consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper.find the magnitude of the man’s force for both designs.
Chapter 11, Problem 066 GO Your answer is partially correct. Try again. In the figure, a small 0.109 kg block slides down a frictionless surface through height h = 1.46 m and then sticks to a uniform vertical rod of mass M = 0.218 kg and length d = 1.55 m. The rod pivots about point O through angle e before momentarily stopping. Find 0. Number Units (degrees) em the tolerance is +/-2% em Click if you would like to Show Work for this question: Open Show Work
A 4 m long horizontal uniform beam of mass 20 kg is supported by a wire as shown in the figure. The wire makes an angle of 23 degrees with the beam. Attached to the beam 1.2 m from the wall is a ball with a mass of 48 kg. What is the tension in the string? K 0 (m)
Just need part B
Problem#1: The coefficient of friction between the inner pulley and the belt is 1/π. Find the maximum value of W that can be supported without rotating the compound pulley P or slipping the belt on the compound pulley P. Pulley B is frictionless. A 200 lb 10 W
Consider the setup shown below. The blocks have masses 3.6 kg and 24 kg. The pulley has mass 7.4 kg, and is a uniform disc with radius 0.23 m. Assume the pulley to be fric- tionless, but the coefficient of friction between the block and the surface is 0.36. a T2 3.6 kg T1 = 0.36 22° 24 kg What is the acceleration of the blocks? As- sume the 24 kg mass is descending with accel- erațion a. The moment of inertia of the disk is - M R? and the acceleration of gravity is 2 9.8 m/s?. Answer in units of m/s?.
The experiment you did in lab is repeated, using a uniform metal bar that is 80.0 cm long instead of the meterstick. Since the bar is uniform, its center of gravity is at its center. The new experiment uses different hooks for hanging the masses from the bar, with mhook 5.0 g. As in the experiment you did in lab, X1 = 5.00 cm, m1 300.0 g, and Xp = 25.0 cm. In the 1 new experiment, you make the same measurements as in your lab and plot x versus The line that is the best fit to your data has slope 3800 cm · g. What is the mass of m2 + mhook the bar?
Please Asap
a. What is the magnitude of acceleration of the block? b. What is the magnitude of the tension force from the block on the cylinder?
Please help me by showing step by step.
Item 9 A garage door is mounted on an overhead rail (Figure 1). The wheels at A and B have rusted so that they do not roll, but rather slide along the track. The coefficient of kinetic friction is 0.54. The distance between the wheels is 2.00 m, and each is 0.50 m from the vertical sides of the door. The door is uniform and weighs 900 N. It is pushed to the left at constant speed by a horizontal force F, that is applied as shown in the figure. Figure B k A K 2.00 m -3.00 m h F 1 of 1 If the distance his 1.60 m, what is the vertical component of the force exerted on the wheel A by the track? Express your answer to two significant figures and include the appropriate units. μA ? nA = Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part B If the distance h is 1.60 m, what is the vertical component of the force exerted on the wheel B by the track? Express your answer with the appropriate units. μÅ ? nB = Value Units Submit Request Answer Part…