A mixing beater consists of three thin rods, each 10.6 cm long. The rods diverge from a central hub, separated from each other by 120°, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has cross-sectional area 4.20 cm? and is soshaped that it has a drag coefficient of 0.620. The drag force on each ball is R =Dp A v2 where D is the drag coefficient, p the density of the fluid, A the cross-sectional area, and v the speed of the object moving through the fluid.(a) Calculate the power input required to spin the beater at 1000 rev/min in water.w(b) The beater is taken out of the water and held in air. If the input power remains the same (it wouldn't, but if it did), what would be the new rotation speed?rev/min

Given data: Length of rod r=10.6 cm. Cross-sectional area of ball A=4.20 cm2. Drag coefficient…

Answered: A mixing beater consists of three thin…

Similar questions

Directions: Assume, unless otherwise specified, that all numbers have at least 3 significant figures. F (N) Students collect data, see graph, for the force involved in stretching a rubber band. The data is well fit by the equation F = 33.65 x0.4971, 12 10 where F is in newtons and x is in meters. One end of the rubber band is attached to a stationary vertical rod and the other end to a 0.3 kg mass. The mass rests on a frictionless horizontal surface. The mass is pulled back such that the rubber band is stretched by 0.8 m from its unstretched length and then released from rest. 4. x (m) 0,1 0.02 0.04 0.06 0.08 A. What is the speed of the mass after it has traveled 0.4 m? B. What is the maximum speed of the object?
When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total gravitational force on the body, F, is supported by the force n exerted by the floor on the toes of one foot. A mechanical model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and e when F, = n = 675 N. (For e, enter the smaller of the two possible values between 0° and 90°.) Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm T = N R = N Need Help? Read It
A speedboat with a mass of 505 kg (including the driver) is tethered to a fixed buoy by a strong 29.7 m cable. The boat's owner loves high speed, but does not really want to go anywhere. So the owner revs up the boat's engine, makes a lot of noise, and runs the boat in circles around the buoy with the cable supplying all the necessary centripetal force. When the tension of the cable is steady at 12300 N, with what force is the boat's engine pushing the boat? Different physics textbooks treat drag force somewhat differently and use different formulas. For the present purpose, take the water's drag force on the boat to be (450 kg/m) × v², where v denotes the boat's speed. Ignore any drag force on the cable. force: N & TOOLS x10
A ladder leans against a wall 5 meters above the ground so a homeowner can clear his gutters of leaves from last fall. The bottom of the ladder just begins to slip when it is 1.7 meters from the wall. What is the coefficient of static friction between the bottom of the ladder and the ground?
A ceiling fan consists of a small cylindrical disk with 5 thin rods coming from the center. The disk has mass md = 2.7 kg and radius R = 0.25 m. The rods each have mass m, = 1.2 kg and length L = 0.86 m.
A 10 m long board has a mass of 7 kg. The left end of the board is against a wall and it sticks straight out like a boom. A rope is tied 1 m from the right end of the board and makes a 44 degree angle with the boom. A 25 kg box hangs 3 m from the right end. Find the tension in the rope.
A wheel of radius 0.269 m, which we can model as a thin disk, is mounted on a frictionless horizontal axis. The mass of the wheel is 2.44 kg. A massless cord wrapped around the wheel is attached to a block of 4.16 kg that slides on a horizontal frictionless surface. If a horizontal force P with a magnitude of 10.1 N is applied to the block as shown below. If the wheel and block start at rest, and the block is moved through a displacement of 2.60 m what is the final angular velocity of the wheel in rad/s, assuming the cord does not slip. P
A 3.0-m -long ladder, as shown in (Figure 1), leans against a frictionless wall. The coefficient of static friction between the ladder and the floor is 0.50. Figure L=3.0 m 1 of 1 Part A What is the minimum angle the ladder can make with the floor without slipping? 0min = Submit VO ΑΣΦ Provide Feedback You have already submitted this answer. Enter a new answer. No credit lost. Try again. ? Previous Answers Request Answer O