A milling operation is performed on an NC machining center. Total travel distance L= 300 mm in a direction parallel to one of the axes of the worktable. Cutting speed = 1.25 m/s and chip load = 0.05 mm. The end milling cutter has four teeth and its diameter = 20 mm. The axis uses a DC servomotor whose output shaft is coupled to a leadscrew with pitch = 6 mm/rev. The feedback sensing device connected to the leadscrew is an optical encoder that emits 250 pulse/rev. Determine (a) feed rate and time to complete the cut along the travel distance L, and (b) rotational speed of the motor and the pulse rate of the encoder at the feed rate indicated.

A milling operation is performed on an NC machining center. Total travel distance L= 300 mm in a direction parallel to one of the axes of the worktable. Cutting speed = 1.25 m/s and chip load = 0.05 mm. The end milling cutter has four teeth and its diameter = 20 mm. The axis uses a DC servomotor whose output shaft is coupled to a leadscrew with pitch = 6 mm/rev. The feedback sensing device connected to the leadscrew is an optical encoder that emits 250 pulse/rev. Determine (a) feed rate and time to complete the cut along the travel distance L, and (b) rotational speed of the motor and the pulse rate of the encoder at the feed rate indicated.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The location of the tool, VT, is not accurately known. Using force control, the robot feels around with the tool tip until it inserts it into the socket (or Goal) at location ST. Once in this "calibration" configuration (in which {G}and {T) are coincident), the position of the robot, T, is derived by reading the joint angle sensors and computing the kinematics. Assuming T and Tare known, give the transform equation to compute the unknown tool frame, WT. {B} {S} {W} 2G {G} ÎT {T} ☆G XT 2T
53 B 36 19 a = 30° B = 79⁰ Y = 0° 0 = 81° 36 radius Find the velocity and acceleration of the bicycle. 4 bar linkage problem. 60deg/s constant CCW angular velocity of the rider's thigh (upper leg), solve the mechanism kinematics and find the bicycle linear velocity and acceleration at this instant. Assume the gear ratio of the bicycle is 1.5. Hint: Use a fixed axis kinematics method with the x- axis along the 61 cm frame from the crank center to rider's pelvis.
A stepper motor serves as the drive unit for the linear joint of an industrial robot. The joint must have an accuracy of 0.25 mm. The motor is attached to a leadscrew through a 2:1 gear reduction (2 turns of the motor for 1 turn of the leadscrew). The pitch of the leadscrew is 5.0 mm. The mechanical errors in the system (due to backlash of the leadscrew and the gear reducer) can be represented by a normal distribution with standard deviation = ±0.05 mm. Specify the number of step angles that the motor must have in order to meet the accuracy requirement.
A input (giriş) N4= 18 m= 2 mm (A-B) d3= 108 mm m= 3 mm (C-D-E-F) How many stages does this gearbox have? O A) 6 Nc= 24 n,= 120 dev/dak (rev/min) Ng= 16 n;= 480 dev/dak (rev/min) na= 720 dev/dak (rev/min) E B) 3 C) 9 O D) 2 O E) 4 output F (çıkış)
For the spherical manipulator shown in the Fig. 1, derive the link parameters using D-H convention. Also find T. Fig.1
Design a single DOF mechanism with 3 outputs. Find kinematic structure and calculate mobility of the mechanism. Prove that it has 1 DOF.
Please give me answer in 45 min. Calculate the minimum technical specifications of a linear pneumatic cylinder that meets the requirements of raising the transfer mechanism in 3 seconds and lowering in 2 seconds.Specifically, the distance to travel (stroke) and diameters.
A slider-crank mechanism is required whose slider is at position 12 cm when its crank is at 90°. Further, the velocity of the slider will be 5 cm/sec leftwards when input crank speed is 1 Rad/sec CCW. At the given position and acceleration of the slider will be 2 cm/sec² leftwards when input crank speed is constant. Design the mechanism and do a position, velocity and acceleration analysis to verify your design.
QUESTION 3 Yo X'o = 0.7, Y'o=-3.7 O X'o = 2, Y'o=2.532 Y1 X'o = 2.532, Y'o=2 10₁ Y2 ............. **** ●--- 1X2 ////// For the Two-link planar manipulator shown above, if the links a₁=a2 =1 If the joint velocities are constant at 0₁'=1, 02'=2, what is the instantaneous velocity of the tool at 01=02= TV4. X'o = -3.7, Y'o=0.7 X1 xo
2. Is the degree of mobility of the hypothetical manipulator kinematic chain equal to the number of degrees of freedom of the manipulator tip.
urgent.
There is a position tolerance applied to a four hole pattern and another position tolerance to a single hole. Calculate the diameter of a pinused as the secondary datum feature B simulator for these position tolerance.