A mild steel specimen originally 400 mm long is pulled in tension with a stress of 510 MPaIf the deformation is entirely elastic, what will be the resultant elongation? The modulusof elasticity of steel is 203 GPa. During the tension test on a steel rod within the elastic region, the following data weremeasured:Applied load= 102 KNOriginal diameter= 25 mmCurrent diameter= 24.993 mmOriginal gauge length= 100 mmCurrent gauge length= 100.1 mmCalculate the Young's modulus and Poisson's ratio.

Given data:- *length of mild steel specimen (L) = 400 mm *stress (σ) =510 Mpa *modulus of elasticity…

A mild steel specimen originally 400 mm long is pulled in tension with a stress of 510 MPa If the deformation is entirely elastic, what will be the resultant elongation? The modulus of elasticity of steel is 203 GPa.

A mild steel specimen originally 400 mm long is pulled in tension with a stress of 510 MPa If the deformation is entirely elastic, what will be the resultant elongation? The modulus of elasticity of steel is 203 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.8 Refer to the following table from ACI Code to determine the maximum spans or minimum thickness for the multi-span one-way slabs shown the following questions. RECESS 2%* AT BALCONY EDGE TABLE 9.5(a) - MINIMUM THICKNESS OF NONPRESTRESSED BEAMS OR ONE-WAY SLABS UNLESS DEFLECTIONS ARE CALCULATED Member Solid one- way slabs SPAN? CANTILEVER Beams or ribbed one- way slabs Minimum thickness, h One end Both ends Simply supported continuous continuous Cantilever Members not supporting or attached to partitions or other construction likely to be damaged by large deflections 1/20 U24 0728 1/10 4/16 /18.5 021 Notes: Values given shall be used directly for members with normalweight concrete and Grade 60 reinforcement. For other conditions, the values shall be modified as follows: a. Choose a uniform slab thickness for all spans in the following diagram. At the cantilevered balcony, keep the same bottom of slab level for ease of formwork. o pa po 7.4' 26:0 48 For lightweight concrete having…
I need the answer as soon as possible
The modulus of elasticity is measured as the secant for a stress at: a) 30% b) 45% c) 25% d) 40%
A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the tótal deformation of the bar if it has a modulus of elasticity E= 28.5 x 10^6 psi. %3D O 0.1378 inches O 0.1338 inches O 0.1352 inches O 0.1364 inches O 0.1423 inches
Calculate the stress and strain at each force interval. Plot a graph of the stress-strain curve. Estimate the yield point of the steel and note its location on the curve. Estimate the ultimate strength of the steel and note its location on the curve.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
A steel specimen is tested in tension. The specimen is 50 mm wide by 25 mm thick in the test region.The specimen yields at a load of 160 kN and fractures at 215 kN. Determine the tensile stress at fracture.
A copper rod with a diameter of 24 mm is subjected to tension within the elastic region. If themodulus of elasticity is 115 GPa and a Poisson’s ratio of 0.34. Determine the force that willproduce a reduction of 0.003 mm in the diameter.
A certain steel has proportionality limit of 300 N/mm² in simple tension. Under a Three Dimensional Stress System, the principal stresses are 150 N/mm² (Tensile), 75 N/mm² (Tensile) and 30 N/mm² (Compressive), μ = 0.3. The factor of safety according to maximum shear stress theory would be
A hollow steel cylinder 3.5m which has an inside diameter and outside diameter of 55mm and 35mm. If the steel carry a load (Your Registration Number ie 1 to 63) KN find the stress in the cylinder also find the deformation in the cylinder if the Modulus of Elasticity is 90 GPA.
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035
A steel plate is subjected to pure shear. The steel has a yield strength of 250 MPa. How muchshear stress can the plate resist before it yields according to the Von-mises yield criterion.