A microphone produces a voltage of 2mV and has an internal resistance of 300 ohm. The microphone is connected to an amplifier with an input impedance of 1k-ohm, an output impedance of 50 ohm, and a voltage gain of 50dB.   The amplifier output is connected to a 75 ohm load. What is the output voltage? I NEED ONLY TYPE SOLUTION Don't give handwritten solution please Don't give diagram

Q: 6. In figure 3. If R1=100, R2=50 N, Vin=0.5V and RL=2002. Find the output voltage. 7. In figure 2.…

A:

Q: Q1/ Determine the output waveform relative to input where input voltage is (what is the name of the…

A:

Q: 3. Collector characteristics for the Ge transistor If VEE =2 V, VCC =12V, and RC = 2k , size RE so…

A:

Q: .a Determine the output voltage for the circuit (a) for each input voltage in (b), (c), and (d). Via…

A:

Q: 24 Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to…

A: Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to 5-V…

Q: (b) Figure 1(b) shows a type of oscillator. Given T=3ms and the duty cycle is 50%. i) Name this…

A: Given: Consider the following figure shows a type of oscillator. Given T=3ms and the duty cycle is…

Q: Q1. In the circuit Figure 1, ß is in range 75 < p s150 , Determine the range in (a) Small signal…

A:

Q: To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the…

A: In given problem ADC is 4 bit hence number of steps(bins) in which analog input is divided is 2n…

Q: 1. Design a clamper to perform the function indicated. Determine the proper value of Voc Calculate…

A: From the input waveform given, the value of input voltage is  Vin = 10V

Q: * Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: Given  The circuit which changes the shape of the input.

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter:  It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: Determine the maximum voltage gain of the amplifier (O/P over I/P) with the output load RL…

A: In the given circuit R1 and R2 can be replaced by Thevinin equivalent. To find the output voltage…

Q: From the figure shown, when S1 is at 1 (toggle at up position) the following statement is not…

A: The given circuit is as shown below,

Q: GE NES LA LT I54-125. 2 DR A VAC ZA S VAC 14 1/24 125 1 250 Vec VP125 AC 1A P VAC MICRO

A: it is a mechanical limiting switch These are often used in low applications this might be used to…

Q: Q1/ Determine the output waveform relative to input where input voltage is (what is the name of the…

A:

Q: What type of regulator is shown in the figure? Vin R2 12kO D₁ 1N4689 5.1V a. IC regulator Ob. Shunt…

A: Type of regulator

Q: * Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: This is the problem of application of diode. The solution is given in the next step.

Q: Find out the expression of the output voltage of each Op-amp in each circuit.

A: It is given that:

Q: 2-adjust the A.C. oscillator to 8 Vp-p & 140Hz,R1=1K,L=400mH, R2-100 ohm

A:

Q: Explain what a 2 stage amplifier is and couplings below with diagrams please!

A: According to the question, we need to explain (1) RC coupled amplifier (2) Direct coupled amplifier…

Q: Electronies Laboratory 100k Vee Figure (5) input eles circuit Var 0 0.1 In Vor Vnr VaE Vu Vu 0.2 0.3…

A: VCE 0 0.1 0.2 0.3 0.4 IB VBE VBE VBE VBE VBE 0 0 0.1 0.2 0.3 0.4 5           10…

Q: This is a block diagram of a 4-bit analog to digital converter (A/D).  Assume the analog input…

A: The solution can be achieved as follows.

Q: Can y help me fast

A:

Q: 2

A: From the given figure, Rf​=10kΩV1​=16V (1) We have to determine the resolution for the given…

Q: 1. Determine the minimum and maximum output voltages for the voltage regulation in Figure below.…

A: Given R1=220 ΩR2=5 kΩ

Q: Eut arm A 017 (1-D) 02 EA 1. arm 03 (1-0) 04 D 2 For a 4 Quadrant DC to DC converter (figure above):…

A:

Q: There is the following bellows pressure gauge with potentiometer: P1 P2 Bellows Eo The range of the…

A: Pressure gauges are used to measure the pressure in a system. It will convert the pressure to a…

Q: 6. Find the output for the below block and check whether it provide Gain or attenuation. Vin=3V Vout…

A: As the blocks are cascade form so the gain will multiply.

Q: What are the components of an electrical circuit? Vdd QI OFF OFF Output Vdd Inputa ON Q4 Inputs ON

A: Above the circuit is NAND Gate A number of NMOS and PMOS collectively =4 when both inputs are high…

Q: IX- A multiple-junction thermocouple circuit that is designed to- a) Decreases the volt generator b)…

A:

Q: VDD M2 RD Vin M₁ C Lo Vout 4M3

A:

Q: n which class of chopper, the output current is always positive, whereas the output voltage could be…

A: Consider the quadrant diagram given below:

Q: Calculate the lc in figure below with beta = 80 Vcc= 12 V 550k www 1.5k

A: From the question, it is given that β=80 Vcc=12 V We know that VBE=0.7 V

Q: * Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: The clamper circuit is used to clamp the input voltage at particular value. And clipper is used to…

Q: 4. Redesign the circuit so that the input voltage of V, has an increase gain of 5 and V2 is reduced…

A: 4) The circuit diagram is given as case 1_ Let's find the gain due to the input voltage V1 Consider…

Q: Q1: Calculate the frequency of oscillation for each circuit in Figure below and identify the type of…

A: It is given that:

Q: Determine the output voltage, Vout when : R1= 10000 R2=12818 Vref=5V

A: