A mass of air is initially at 206°C at pressure of 7bar and having volume of 0.03m³.The air is expanded at constant pressure to 0.09m³,a polytropic process with index (1.5) is then carried out followed by a constant temperature process which completes the cycle. Determine : 1. The total work done on or by the system 2. The ratio of the rejected to added heat

Q: 4- A piston-cylinder device, with a set of stops on the top, initially contains 3 kg of water at 200…

A:

Q: A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston- cylinder device…

A:

Q: Inside a piston-cylinder device there is 5 kg of a moist water vapor at 125 kPa. At the beginning…

A:

Q: A piston-cylinder assembly contains 3 lb of water vapor, initially at 300F and 20 lbf/in2 is…

A: To find (a) The total work done during the process W. (b) The total change in entropy during the…

Q: A 10-ft' tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is…

A:

Q: A piston/cylinder arrangement initially contains water at 1800 Kpa & 275 oC. This water, from its…

A: Isentropic process is a process in which entropy remains constant and change in entropy is zero.…

Q: A tank contains R134a initially at 3 degrees Celsius with a quality of 0.25. the pressure is held…

A: Given: Initial state T1=3oCx1=0.25 Supply line: Psupply=975 kPaTsupply=118oC Final State: m2=20…

Q: 1 kg air undergoes reversible heating at constant P from Ti = 300K and Pi = 1 bar until the volume…

A: Given data:- The mass of air (m) = 1 kg                       The initial temperature (T1) = 300K…

Q: 1.2 1 kg of a fluid is compressed reversibly according to a law pe 0.25, where p is in bar and r is…

A: Given data Pv = 0.25 Final volume = 1/4 initial volume

Q: 13. A gas is transferred to an empty 0.7m cylinder until the pressure reaches 9MPaa. The temperature…

A:

Q: Calculate the net work produced by this cycle, the required heat input to the cycle and its thermal…

A: hjjhjhjhkjk

Q: A piston-cylinder device contains 0.8 kg of steam at 320° C and I MPa. Steam is cooled at constant…

A:

Q: A Piston-cylinder system initially contains R-134a refrigerant at 2.8 bar and 40BC temperature, and…

A:

Q: certain quantity of gas with an initial condition of 14 bar, 0.08 m3, and 450 K expands at constant…

A: Given Data State 1: 14 bar, 0.08 m3 and 450 K State 2: 0.25 m3, 14 bar

Q: Water, initially a saturated liquid at 100°C, is contained in a piston-cylinder assembly. The water…

A:

Q: Solve the following questions using Steam Table: 1. Determine T, h, s, u and v of saturated steam…

A: Given conditions Condition 1 Pressure = 1.4 MPa With a superheat of 100oC   Condition 2 Pressure =…

Q: g air with initial temperature of 100°C expands at a constant pressure of 2 bar to reach to a final…

A:

Q: Two rigid tanks A and B are connected by a valve. Tank A contains 0.6 of water at 550 kPa and 38…

A:

Q: Problem No 1: A 1.5 kg of gas expands in a closed system from 6.5 kPaa and 60 liters to 100 liters.…

A: Given : Initial pressure P1 = 6.5 kPa V1 = 60 litres = 60/1000 =0.06 m3 V2 = 100 litres = 100/1000 =…

Q: Two vessels A and B of different sizes are connected by a pipe with a valve. Vessel A contains 140 L…

A:

Q: Saturated steam at 329.3 degree Celsius undergoes an isentropic process until it reaches a pressure…

A: Given Data The temperature of the steam is T=329.3°C=602.3 K.  The pressure of the steam is P=1.6…

Q: A frictionless piston-cylinder device contains 2.5 kg of nitrogen at 100 kPa and 250 K. Nitrogen is…

A: According to the given dataThe mass of nitrogen is m = 2.5 kgThe initial pressure is P1 = 100 kPaThe…

Q: I need help with the steps of this practice problem. Can I get help to solve it ? A piston cylinder…

A: Consider the diagram shown below for the given processes. Given data:

Q: For the situations below briefly explain how you obtained the values and provide the numerical…

A: It is required to determine properties for given process

Q: /

A:

Q: Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition.…

A:

Q: 1 kg of steam in a piston / cylinder assembly is initially at 357.933 \ deg C and 2685.66 kPa. It is…

A:

Q: A ball having 7.62 cm radius contains air (R = 53.3 lbf – ft/lbm - R) at 235.3 psig and 550R. After…

A: Given Data, r= radius of the ball = 7.62 cm = 7.62x0.393701 = 3 inch V = Volume of the ball =…

Q: 2) A 0.8 m rigid tank contains refrigerant-134a initially at 100 kPa and 25 percent quality. Heat is…

A: Data given-  V = 0.8 m3  P1 = 100 kPa  X1 = 0.25  P2 = 500 kPa

Q: A steam boiler initially contains (5 m3) of steam and (5 m3) of water at (10 bar). Steam is taken…

A: Given:P=10 barVs1=5 m3Vw1=5 m3Vw2=4 m3 Given:

Q: What's the total boundary work   _____kJ ?

A: It is given that mass of carbon dioxide (m)= 1 kg Initial pressure (P1) = 500 KPa Initial…

Q: 2. A 10-ft³ tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is…

A:

Q: In a fixed volume, 0.3 m³ container, initially there is refrigerant R-134a at 6 °C. Initially, 60%…

A:

Q: Two tanks connected with 2. each other as shown. The first one has 2 kg of water at P=200 kPa, V, =…

A:

Q: Air enters the cylinder of a 4-stroke gasoline engine at 33°C and 101.2 kPa. Engine clearance is…

A: Given data, P1 = 101.2 kPa T1 = 33°C =306K Vc =10.5% of V Q input  = 2600 kJ/kg

Q: A piston-cylinder system contains 1 kg of air at (V1, P1, T1). The air is heated at constant…

A: Given data: The mass of the air is, m=1 kg. The equation of polytropic compression curve is, PV3=C.…

Q: An insulated cylinder-plunger device with a constant load contains 2 L of saturated liquid water at…

A: Given: The volume of saturated liquid water, V = 2 L The temperature of saturated liquid water, T1 =…

Q: 1) A piston with water vapor at a pressure of 300 kPa and a temperature of 175 oC in the cylinder…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: a cylinder and piston arrangement contains 2 kg of R-134a at 150 kPa, 60 C. The piston is now moved…

A: Given data: Initial conditions: Mass = m = 2 kg Substance : R-134a Pressure = 150 kPa Temperature =…

Q: A piston cylinder contains 0.64 kg of air initially at 450 kPa and 225 °C, now the air expands in a…

A: We have to Determine the amount of work during this process (kJ