A mass of 10 g of nitrogen is contained in the springloaded piston–cylinder device shown in Fig. P4–54. The spring constant is 1 kN/m, and the piston diameter is 10 cm. When the spring exerts no force against the piston, the nitrogen is at 120 kPa and 27°C. The device is now heated until its volume is 10 percent greater than the original volume. Determine the change in the specific internal energy and enthalpy of the nitrogen.

Q: A 14-ft tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is…

A: Given data as per the question The volume of tank= 14 ft3 =0.396436 m3 Initial pressure =14.7 psia…

Q: (b) A mass of 5 kg of saturated water vapor at 300 kPa is heated at constant pressure until the…

A: To find: The workdone by the steam during this process and sketch the process on P-v diagram with…

Q: A cast aluminum solid cylinder of 7 cm diameter (in standing straight up position), fits loosely…

A:

Q: What can make welding in the 2G vertical fixed pipe position difficult?

A: The following is how the 2G welding positions are used. 1. Vertical position is used when using 2G…

Q: A 0.04-m3 piston-cylinder device contains 1.5 kg of argon at a pressure of 507 kPa. The piston is…

A: mass of the argon (m) = 1.5 kgInitial volume of the argon (V 1)=0.04 m³Initial pressure of the argon…

Q: ,determine the tenSion in each rope,

A:

Q: A reciprocating cylinder contains water at a density of 0.01019 kg / liter at a pressure of 0.8 mpa.…

A: Given   Density = 0.01019 kg / liter                = 10.19 kg/m3 pressure = 0.8 MPa Find     The…

Q: Saturated vapor at 55°C is put under pressure to decrease the volume by one percent during an…

A:

Q: 3-34 10 kg of R-134a fills a 1.115 m³ rigid container at an initial temperature of -30°C. The…

A: Given : The mass of refrigrant is The  volume is The initial temperature is The final pressure is

Q: A piston - cylinder device contains 1 kg of saturated water mixture with a quality of x = 0.23 and…

A:

Q: (4) A mass of 3 kg of R-134a fill a piston-cylinder device with and initial volume of 0.279 m³ at a…

A: Refrigerant R-134a, also known as 1,1,1,2-tetrafluoroethane, R-134a, Freon 134a, Forane 134a,…

Q: A 10-kg mass of superheated refrigerant(R-22) at 1.2 MPa and 70°C is cooled at constant pressure…

A:

Q: A 3-ft3 adiabatic rigid container is divided into two equal volumes by a thin membrane, as shown in…

A:

Q: A piston-cylinder device initially contains 0.3 gm of steam at 200kPa and 400°C. Now the steam is…

A:

Q: A 3000 cm' tank initially contains compressed air at 600 kPag and 28 °C. Determine the mass of air…

A:

Q: 4. 0.5 kg of steam at 250°C is enclosed behind a piston in a cylin 0.9MPa. with the piston rigidly…

A: Givenm=0.5kgT1=250oCP1=0.9MPaP2=0.7MPa

Q: A rigid tank contains 20 Ibm of air at 50 psi and 80°F. The air is now heated until its pressure is…

A: The solution is given below

Q: A piston-cylinder device contains 4 kg of nitrogen initially at 100 kPa and 25°C. Nitrogen is now…

A:

Q: Two different piston – cylinder devices each contain 1 kg of air. Initially, the temperature T = 300…

A:

Q: A piston–cylinder device initially contains 1 kg saturated liquid water at 200°C. Now heat is…

A:

Q: A cylinder fitted with a piston has a volume 0.1 m^3 and contains 0.5 kg of steam at 500 kPa. How…

A:

Q: A 15 liter rigid bottle contains 15 kg of the refrigerant R-134A and it is at a temperature of 20°C.…

A: Given that, Mass of the refrigerant R-134a, m=15 kg,Volume of bottle, V=15 liter,Temperature of…

Q: The gas is compressed from an initial state of 3 0.35 m and 105 kPa to a final state of 0.14 m 3 and…

A:

Q: In this example, water is contained in a rigid container with a tight fitting lid. With a pressure…

A:

Q: Argon in the amount of 1.5 kg fills a 0.04-m3 piston-cylinder device at 554 kPa. The piston is now…

A: Given data:- The mass of argon (m) = 1.5 kg                     The initial volume…

Q: A piston-cylinder device is filled with 2.75 kg of carbon monoxide (CO). The inital lume and…

A:

Q: Water is contained in a cylinder/piston arrangement fitted with upper stops which limit the volume…

A:

Q: A closed vertical cylinder containing 0.3 kg of nitrogen at 90°C is fitted with a weighted,…

A: Given: The mass of nitrogen gas is m=0.3 kg. The initial temperature of nitrogen gas is T1=90°C. The…

Q: Air is contained in a piston-cylinder arrangement with an initial volume of 0.02 m³ and at an…

A:

Q: contains saturated vapor only. Determine (a) the volume of the tank, (b) the final temperature and…

A: Given: m= 1.6 kg state 1 saturated liquid T1= 220oC V2=4V1 State 2 saturated vapor To determine: The…

Q: A 0.8-m3 rigid tank contains nitrogen gas at 600 kPa and 300 K. Now the gas is compressed…

A:

Q: A mass of 10 g of oxygen fill a weighted piston– cylinder device at 20 kPa and 100°C. The device is…

A: Given: The mass of the oxygen is m=10 g. The initial pressure and temperature of the cylinder are…

Q: A rigid tank contains 15 kg of water at 75°C. If 3 kg the water is in the vapor form and the rest is…

A:

Q: A 12-ft3 tank contains oxygen at 15 psia and 80◦F. A paddle wheel within the tank is rotated until…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.