A masonry dam of trapezoidal cross section, with one face vertical has thickness of 60cm at the top, 3.70m at the base, and has a height of 7.40m. What is the depth of water on the vertical face if the resultant intersects the base at the downstream edge of the middle third? Assume that the uplift pressure varies uniformly from full hydrostatic at the heel to zero at the toe

A masonry dam of trapezoidal cross section, with one face vertical has thickness of 60cm at the top, 3.70m at the base, and has a height of 7.40m. What is the depth of water on the vertical face if the resultant intersects the base at the downstream edge of the middle third? Assume that the uplift pressure varies uniformly from full hydrostatic at the heel to zero at the toe

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A gravity dam is designed such that the HFL is at a height of 17m from the base. At the downstream of the dam, water is always filled upto a height of 1.5m. What will be the total uplift force exerted on the dam due to seepage if a drainage gallery is provided at a distance of 4m from the heel. Take total width of the dam as 10m.
1. A rectangular dam with base equivalent to 2.5-meters and height equivalent to 6-meters holds water with an upstream height of 4.5-meters. Compute for the factor of safety against sliding and overturning. Unit weight of concrete is 23.54 kN/cu.m. Consider 1 meter length strip. Disregard hydrostatic uplift pressure. The coefficient between the dam and the foundation is 0.4.
A masonry dam of trapezoidal cross section, with one face vertical, has a thickness of 2ft at the top and 10ft at the bottom. It is 22ft high and has a horizontal base. The inclined face is subjected to water pressure, the water standing to a depth of 15ft above the base. The weight of the masonry is 150lb per cu ft. If there is no hydrostatic uplift, where will the resultant pressure intersect the base? Is this a good design?
For a linear stress variation over the base of the dam and neglecting hydrostatic uplift. 70m note: sg concrete=2.5 40m 60m 10 6. Locate where the resultant crosses the base a. 5.59 m b. 6.28 m c. 8.42 m d. 10.51 m 7. Compute the maximum compressive stress at the base a. 1390 kPa b. 1186 kPa с. 463 kPa d. 508 kPa
A masonry dam with one end face vertical, has a base 3.3 m and 7.2 m high. The vertical face is subjected to water pressure, the (s 2.4) triangular in cross section, water standing 4.5 Neglect hydrostatic uplift. Compute the following: above the base of the dam. a. The vertical reaction of the foundation. b. Distance of the vertical reaction from the heel. c. Factor of safety against overturning.
e. unit horizontal shearing stress at the base in kPa
1. A masonry dam of trapezoidal cross section, with one face vertical and horizontal base. The dam is 8-m high and has a thickness of 70-cm at the top and 4-m at the bottom. The unit weight of the masonry is 23.450 N/cu.m. What is the depth of water on the vertical side if the resultant force intersects the base at the downstream edge of the middle third. Neglect the hydrostatic uplift.
Determine the sliding factor of safety and the heel and toe stresses for a triangle gravity dam (25m bed width and 20m height) with the following data: (neglect ice force and use e = 1.0m) 7 w=10 Kn/m³, 7 c-24 Kn/m³, s-1.8 Kn/m³, height of silt 2m, hw=0.5m, = 30° and free board 2m.
2. A triangular dam 3 m wide at the base and 5.6m high weighs 23.5 kN/m3. a. What depth of water on its vertical upstream face will make the factor of safety againstovertuming 2.07b.What depth of water on its vertical upstream face will make the safety factor against sliding1.5 assuming a coefficient of 0.6?
A masonry dam of a trapezoidal section with one face vertical is 0.60m thick at the top and 3m at the bottom. It is 6.60m high and has a horizontal base. On the inclined face water stands 4.5m deep. Assume sp.gr. = 2.4 for the dam and hydrostatic uplift varies. from 60% at the heel to zero at the toe. Use sp.gr. = 7.4 for concrete. c) What is the factor of safety against overturning? d.) What is the factor of safety against sliding assuming M=0.51 e) what is the intensity of pressure at the toe?