A makeshift compact torsional spring is made of steel (Gst = 11,000,000 psi) and is composed of a solid inner shaft from C to B and a hollow shaft from A to B. The solid and hollow shafts are connected through an unyielding ring at B. The necessary radiuses are shown below. Assume the ring attached to the hollow shaft at A is rigid with no rotation. If the torque applied T at point C is 2 kip-in, find the: a. Maximum shear stress in the solid inner shaft, ksi b. Maximum shear stress in the hollow outer shaft, ksi c Angle of twist at point C, degrees 12 in. 12 in. 0.75 in. T 1 in. 0.6 in C

A makeshift compact torsional spring is made of steel (Gst = 11,000,000 psi) and is composed of a solid inner shaft from C to B and a hollow shaft from A to B. The solid and hollow shafts are connected through an unyielding ring at B. The necessary radiuses are shown below. Assume the ring attached to the hollow shaft at A is rigid with no rotation. If the torque applied T at point C is 2 kip-in, find the: a. Maximum shear stress in the solid inner shaft, ksi b. Maximum shear stress in the hollow outer shaft, ksi c Angle of twist at point C, degrees 12 in. 12 in. 0.75 in. T 1 in. 0.6 in C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
subject: statics of rigid bodiesPlease be tidy and readable, as well as presenting your solutions.
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
Please sir give me answer immediately
For the mechanism shown in the figure, determine the torque TA required at crank AB to maintain static equilibrium of a 250-lb force FT acting on link 6 (E) when theta = -330 grades. The Dimensions are: h = 16, d = 20 and AB = 8 (inch units). d ΤΑ & c
Question 2 A crank slider has a crank of length 0.04m and a coupler of length 0.08m as shown in the figure. The crank mass is 0.25 kg and is located at the center of a slender link (IG = 1/12*m*1²). The coupler is massless. The slider has a mass of 0.25 kg and a load of -10N in the i direction. Find the torque required to drive the mechanism and forces at O2 and B for a crank angle of 90° if the crank has a steady state rotation of 1000 RPM in the counterclockwise direction. А b = .08m m, = 0.0 I, = 0.0 В T, 0,, wz, a, 0, wz, a, 2' 3' 3' 0, F, = -10î N m, = 0.25 kg I, = 0
For the system of springs shown below derive the formula for the overallstiffness cΣ and calculate the overall displacement s if F=200 N, c1=2300 N/m, andc2=2100 N/m.
e The two-steel shaft shown in figure have the same diameter and weight 180 lb each. Neglect the friction at all contact surfaces and find the reaction of the wall at A on the lower shaft
Q The two-steel shaft shown in figure have the same diameter and weight 170 lb each. Neglect the friction at all contact surfaces and find the reaction of the wall at A on the lower shaft
The transmission is made up of four helical gears and two bearings conics that are located at point A and point B. Following the arrangement of coordinate axes shown In Figure 1, the forces acting on the pitch circle of the pinion (25 teeth) and the gear (50 teeth) with a transmitted torque of 868 Nm between the gear location. Obtain the reactions (Fby, Fay, Faz, Fbz) of the bearings
Q2: Design a torsion spring with an initial torque of T, =2000Nmm and a maximum torque of T2 =8000Nmm. The minimum angular deflection is oi 10 and the maximum angular deflection is p2 =400. The spring is to be installed in a steadily operating machine.