A magnetic core with an air gap is shown below. For a relative permeability is 3500, and the space free permeability is 4πx 107 H/m, find the reluctance of the gap, assuming a 4 percent increase in the effective air-gap area to account for fringing. 5 cm gap 0.15 cm 5 cm 40 cm 5 cm 20 cm N Answer: Rgap core depth = 10 cm KA.t./Wb. 15 cm

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Difference in circuit breakerand isolator.

A: Isolator is also known as the disconnector. As the name suggest they are the isolating switches…

Q: mostly don't know how to do question (d) and (e)

A:

Q: What is wrong with the switch wiring? O Jacket is not removed far enough O Nothing O Terminations…

A: In a wiring, usually a phase wire of the supply is connected to one of the terminals of the device…

Q: Does the NEC procide the minium or the maximum standard?

A: In order to protect humans and properties from the hazards while using electricity, some minimum…

Q: A/An ________ captures different types of signals from the human body and convert them into…

A: The solution is given below.

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: Spacing between receptacles in a kitchen area that is NOT countertop space is? No more than 6…

A: Countertop - The best kitchen countertop material, as previous posters said, depends on what you…

Q: What assumptions can you make regarding the following receptacle wiring? Check all that apply.

A: A split pair is a wiring fault in which two twisted pair wires are linked instead with two wires…

Q: -6) Solid grounding is used for voltages

A: Solid is used for the voltages below:

Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…

A:

Q: What should I enter in the box for final answer? It is asking for maximum amount of noise not…

A: Given:Solution of a problem, The maximum amount of noise, the circuit can tolerate is the noise…

Q: ladder diagram for three circuits, circuit A is one lampholder and one duplex receptacle controlled…

A: According to the question, we need to design a ladder diagram for three circuits, circuit A is one…

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: Where a 2 1/2 inch conduit enters an angle pull box with three 400 MCM type THHN conductors and a 2…

A: For angle pulls, the distance between each raceway entry inside the baox and the opposite wall of…

Q: The nec requires that the disconnecting means for central heating equipment other than Fixed…

A: Article 422 of National electric code (NEC) have rules and regulation of using central heating…

Q: It is often desirable in designing an electric wiring system to be able to control a single…

A: The diagram is shown as

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.