A magnetic circuit made of mild steel is arranged as shown in Fig.3. The central limb is wound with 500 turns and has a cross-sectional area of 800 mm². Each of the outer limbs has a cross-sectional area of 500 mm². The air-gap has a length of 1mm. Calculate the current required to set up a flux of 1.3 mWb in the central limb. Take μ-600 and neglect leakage. -120 mm 2-300 mm 6₁ Fig.3 -1mm

A magnetic circuit made of mild steel is arranged as shown in Fig.3. The central limb is wound with 500 turns and has a cross-sectional area of 800 mm². Each of the outer limbs has a cross-sectional area of 500 mm². The air-gap has a length of 1mm. Calculate the current required to set up a flux of 1.3 mWb in the central limb. Take μ-600 and neglect leakage. -120 mm 2-300 mm 6₁ Fig.3 -1mm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Hurry
1. A magnetic circuit constructed of sheet steel has an average length of 1.5 m and cross sectional area of 0.025 m². A 50 turns coil wound on the ring has a resistance of 0.8 Q and draws 4 A from A DC supply. The relative permeability is 5000. Determine a) The flux density. b) Voltage applied. c) If the material is replaced with another material with a relative permeability of 3000 and keeping the other parameters as it is then calculate the new flux and explain what happened.
The magnetic circuit shown below has mean magnetic path of 0.5 m, a relative permeability of 1000, and a uniform cross sectional area equal to 5×104 m². The coil has 120 turns and, when connected to a 120 v, 60 Hz voltage source, draws 5 A. Determine the inductance of the coil in Henry. Give your answers correct to 3 decimal places. Answer:
Consider the magnetic circuit shown in figure u = 1000 µo S2 S, S2 5 cm T04 cm 5 cm S2 S, 6 cm If S1= 5 cm2 and S2 = 10 cm2 then the total reluctance of the circuit will be 6 cm 14 cm S2 9/(20p0) 9/(40μ0) 9/(30μ0) 9/(10μ0)
Consider the magnetic circuit given in below figure with parameters: u=153 Ho, d1=9 cm, d236.2 cm, d3=7.9 cm, da=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 d, Tolerance + 0.1 relative
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
O Determine Vo and to for the nertworks 20 V 12V Si 本e ZSi 34.7kn Vo 23.2ka GAAS (a) + I6V (6) o1个な5 !s !5 A 4.7k Ce) d-4v
When a 5 A current is made to flow through a coil of 20 turns produce a flux if 10 wb.Find the voltage across the coil if the rate if change if current through the coil is 8 mA/s.
A magnetic circuit constructed of sheet steel has an average length of 1.5 m and cross sectional area of 0.025 m². A 50 turns coil wound on the ring has a resistance of 0.8 N and draws 4 A from A DC supply. The relative permeability is 5000. Determine a) The flux density. b) Voltage applied. c) If the material is replaced with another material with a relative permeability of 3000 and keeping the other parameters as it is then calculate the new flux and explain what happened. 1.
The full-scale deflecting torque of a 20 A moving-iron ammeter is 6 x 10-5 N-m. What is the rate of change of self-inductance with respect to the deflection of the pointer of the ammeter at full scale?
I need answer within 20 minutes please please with my best wishes
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm