A magnetic circuit constructed of sheet steel has an average length of l1.5 m and cross sectional area of 0.025 m². A 50 turns coil wound on the ring has a resistance of 0.8 N and draws 4 A from A DC supply. The relative permeability is 5000. Determine a) The flux density. b) Voltage applied. c) If the material is replaced with another material with a relative permeability of 3000 and keeping the other parameters as it is then calculate the new flux and explain what happened. 1.

A magnetic circuit constructed of sheet steel has an average length of l1.5 m and cross sectional area of 0.025 m². A 50 turns coil wound on the ring has a resistance of 0.8 N and draws 4 A from A DC supply. The relative permeability is 5000. Determine a) The flux density. b) Voltage applied. c) If the material is replaced with another material with a relative permeability of 3000 and keeping the other parameters as it is then calculate the new flux and explain what happened. 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 5 cm 15 cm 45 cm 15 cm 15 cm 10 cm
A magnetic circuit has 150 turns-coil, the cross- sectional area 5 x 10-4 m2 and the length of the magnetic circuit 25 x 10-2 m. What are the values of magnetic field intensity and relatíve permeability when the current is 2 A and total flux is 0.3 x 10-3 Wb? (a) 1200 AT/m and 397.9 (b) 300 AT/m and 500 x 10-6 (c) 300 AT/m and 397.9 (d) 1200 AT/m and 500 x 10-6
14. A coil with 150 turns is wound over a 200 cm a cylinder iron core whose relative permeability is 250. If a current of 2 A is pass through the coil, determine the flux density in the core. a. 0.04 T b. 0.07 T c. 0.12 T d. 0.10 T
Q1. Figure 1 shows the magnetic circuit with cross section area of core, 1000 mm2 and current source, 10 mA. By assuming the absolute permeability of core is 2.513x103 H/m, analyze the circuit and determine the following parameters: a. Draw the equivalent Ampere Circuital Law model b. Total reluctance of magnetic circuit c. Magnetic flux at centre and both sided d. Magnetic flux density at centre and air gaps e. Magnetic flux strength at centre and air gaps f. Briefly explain, effect to the magnetic circuit if the length of air gaps keep decreasing and increasing. at 7 cm 30 cm 30 cm 7 cm 7 cm 30 cm 1 cm 400 turns 1 cm 7 cm Figure 1 B-H CURVE BIT) 16 Sheet steel Cast steel 14 12 1.0 08 Cast iron 0.6 04 0.2 H(AUm) 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Solve all parts.
The length of a magnetic circuit in a moving iron instrument is 300mm. The coil around the soft-iron core has 360 turns and takes a current of 1.75 A. The core is square in section with sides of 20 mm. Takethe relative permeability of soft iron as 1100. Determine the flux density
A straight long wire is carrying a current of 1000 A. Find the flux density at a point 1 ft from the wire.
3. A transformer core with an effective mean path length of 10 in has a 300-turn coil wrapped around one leg. Its cross-sectional area is 0.25 in2, and its magnetization curve is shown below. If current of 0.25 A is flowing in the coil, what is the total flux in the core? What is the flux density? 2.8 2.6 24 22 2.0 L8 16 14 12 0.6 04 0.2 10 20 30 40 50 100 200 300 500 1000 2000 5000 Magnetizing intensity H. A-tumsim [1.27 T, 0.000205 Wb] Flux demity, T