0.37 kg,A machine part as shown in following figure consists of three disks linked by light weight struts. Use mAmB = 0.51 kg, mc = 0.2 kg, a = 0.59 m, b = 0.82 m and c = 1.0101980004 m.Axis throughdisks B and CBmBCаAxis through disk A(perpendicular to planeof figure)AmcbmAa)What is this body's moment of inertia in kg/m2 about an axis through the centre of disk A, perpendicular to the plane of thediagram? Insert your answer correct up to at least a third decimal place.b)What is the moment of inertia in kg/m2 about an axis through the centres of disk B and C? Insert your answer correct up toat least a third decimal place.c)What is the body's kinetic energy in Joule if it rotates about the axis through A with angular speed w = 72 rad/s? Insertyour answer correct up to at least a third decimal place.

Answered: Image /qna-images/answer/551b706e-df61-4720-987f-9aac9dd92e06.jpg

Answered: A machine part as shown in following…

A machine part as shown in following figure consists of three disks linked by light weight struts. Use ma = 0.37 kg, mB = 0.51 kg, mc = 0.2 kg, a = 0.59 m, b = 0.82 m and c = 1.0101980004 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

La Figure: Compression spring The squared type of compression spring has total 8 coils shown in the figure. The spring is made of music wire with wire diameter and mean diameter of 0.30 inch and 3.0 inch respectively. Initially the free length of the compression spring was proposed as 3.75 inch. Is this safe to compress the spring to the solid length (L.) considering the factor of safety 1.5? If it is safe why it is safe? Show your calculation. If this is not safe, propose the maximum free length of this spring.
The figure shows the combined design of an angular contact ball bearing on two fulcrums. The radial loads R1 and R2 and axial load Fa of bearings 1 and 2 are shown in the figure. The relationship between the derived axial force S and radial load R is: S = 0.25R. Calculate the actual axial force of bearing 1 and bearing 2? Fa= 360N R1=4000N R2=4250N Problem 5) Figure
Requlred Information A countershaft carrying two V-belt pulleys Is shown In the figure. Pulley A recelves power from a motor through a belt with the belt tensions shown. The power Is transmitted through the shaft and dellivered to the belt on pulley B. Assume the belt tenslon on the loose side at B Is 15 percent of the tension on the tight side. Glven B(dg) = 400 mm, TA = 575 N, and TỊA2) = 3835.25 N. 300 450 400 TIA T(A2Y `150 250 dia. B(da) 20 dia. B At the point of maximum bending moment, determine the bending stress and the torslonal shear stress. The bending stress at the point of maximum bending moment is [.09515 MPа. The torslonal shear stress at the point of maximum bending moment is 259.442 MPа.
A cable and pulley system at D is used tobring a 230-kg pole (ACB) to a vertical position, asshown in the figure part a. The cable has tensile forceT and is attached at C. The length L of the pole is6.0 m, the outer diameter is d = 140 mm, and the wallthickness is t = 12 mm. The pole pivots about a pin atA in figure part b. The allowable shear stress in the pinis 60 MPa and the allowable bearing stress is 90 MPa.Find the minimum diameter of the pin at A inorder to support the weight of the pole in the positionshown in the figure part a.
Question 2 A crank slider has a crank of length 0.04m and a coupler of length 0.08m as shown in the figure. The crank mass is 0.25 kg and is located at the center of a slender link (IG = 1/12*m*1²). The coupler is massless. The slider has a mass of 0.25 kg and a load of -10N in the i direction. Find the torque required to drive the mechanism and forces at O2 and B for a crank angle of 90° if the crank has a steady state rotation of 1000 RPM in the counterclockwise direction. А b = .08m m, = 0.0 I, = 0.0 В T, 0,, wz, a, 0, wz, a, 2' 3' 3' 0, F, = -10î N m, = 0.25 kg I, = 0
u need a table a-9 someone here has that as they answered my question before
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces Fg at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 10 ww ww
Please ans as. Soon possible
Solve the problem and don't copy wrong solution from another website!!