A machine makes two components; call them types A and B. It takes 250 seconds to switch production between the component types. During that time, no production occurs. When in production, each unit of A or B requires 0.5 second to be completed. The two components, A and B, are combined in an assembly process to make a final product; call it C. The assembly step can combine the two components into 1 unit every 2 seconds, or 30 units per minute. Assume there is ample demand. Suppose the machine rotates between one batch of 1,000 untis of A and 1,000 units of B. In that case, what is the capacity of the machine in component pairs per minute, where a component pair is one unit of A and one unit of B? answer: __________ component pair per minute

Q: Kaizen is similar to TQM in that both are focused on continuous improvement. * a. True b. False Line…

A: Kaizen refers to the change for the betterment of the organisation along with it TQM (Total quality…

Q: What is the purpose of process improvement techniques like Six Sigma and Lean?

A: Improvement techniques like Six Sigma and Lean:Process improvement methodologies such as Six Sigma…

Q: Which of these will be addressed if we pursue a value stream mapping? The problems faced by the…

A: Value stream mapping  - VSM It is a visual depiction to improve the flow of manufacturing in an…

Q: What are the two Constituents of JIDOKA a. Zero defects, Andon O b. Auto Line Stop,Least WIP c.…

A: Lean methodology is described as a process of optimization of energy, effort, resources, and people…

Q: A manager wants to determine the number of containers to use for incoming parts for a kanbansystem…

A: Hence, the number of containers that should be used is 3.

Q: A checklist is a type of: Okaizen. O poka-yoke. flowchart O kanban. O Pareto chart 00000

A: A checklist is a type of poka-yoke that helps to ensure completeness and consistency. It helps to…

Q: Jose just found out that at his part-time job in the restaurant, the manager was replacing all of…

A: McDonaldization at a workplace would include,  Efficiency Calculability Predictability and  Control

Q: A company is using a Kanban system with 2 containers, each holding 50 parts, between a downstream…

A: Efficiency is the ability to reduce or eliminate the wastage of resources, money, and time in an…

Q: At Naoki's Jewelry Store, there are fine jewels, expert employees, and modern security features.…

A: Operations management is a vast concept that not only includes inventory and production-related…

Q: With zero inspections we can know if the process is under control or not.

A: A company is made up of many processes and practises that must be followed in order for it to…

Q: 8 Lean production and just-in-time concepts became important ______. a in the mid 1980s, thanks to…

A: Lean manufacturing is a method for estimating and lessening inventory including streamlining…

Q: Which of the following pertains to productivity improvement? A Tightening the inspection at the…

A: The following steps will contribute to the Productivity improvement:-  Tightening the inspection at…

Q: A manager wants to determine the number of containers to use for incoming parts for a kanban system…

A: I would now determine the number of containers,

Q: The grouping of equipment with respect to the operation that are expected to perform similar work…

A: In assembling, office design comprises of arranging the plant site with lines, structures,…

Q: A machine cycle, or process loop, contains four steps. Which proportion of a machine's cycle time is…

A: A machine cycle, also known as a process loop, is a series of stages that a machine takes to…

Q: snip

A: Revising a process such that its desired outcome is the only outcome possible, also known casually…

Q: TQM methodology talks of improving the variability of any process to achieve near Zero defects,…

A: Quality management is described as the process of overseeing different tasks and activities that are…

Q: Is it accurate to say that lean management has a propensity to ignore some aspects of an…

A: Lean management is a popular approach used by many organizations to streamline operations, reduce…

Q: ) Silvercrest Manufacturing Ltd. is using Kanban containers. There are two adjacent work centres, a…

A: The objective of the question is to calculate the number of Kanban containers needed in the system.…

Q: An assembly station is asked to process 100 circuit boards per hour. It takes 20 minutes to receive…

A: Below is the solution:-

Q: The term for safety time added to chains other than the critical chain is: Feeding buffer, first…

A: Feeding Buffer:  It is a safety added to the places where chains of tasks which are non critical…

Q: Diseconomies of scale is where the cost per unit increase as volume of output increases. Select one:…

A: The Diseconomy of scale arises due to several reasons but it is broadly categorized into internal…

Q: A baking operation reduces the amount of variation in the oven temperature. This is anexample of…

A: The Robust Design approach significantly increases engineering efficiency. Robust Design focuses on…

Q: Does the process eliminate steps that do not add value?

A: The concept of lean manufacturing or production is nothing but the process of relentlessly working…

Q: To avoid errors, error prevention should be done before error detection and correction * True False

A: To recognize and address the mistakes, extra pieces are added to the information bits at the hour of…

Q: Screen Printing works best with: Group of answer choices Shorter Yardages of Fabric…

A: Screen printing is a printing method where ink is applied onto a substrate such as paper or fabric…

Q: true or false- Five different products on a pallet being moved, is equal to one unit load.

A: Block Pallets. These beds are known for their four-way passage, which means they can be gotten to by…

Q: Which of the following statements about kanban are accurate?a. Deploying the kanban system leads to…

A: Kanban is an inventory management methodology that enables businesses to store only the components…

Q: minimum 4 checks per hour, maximum 15 minutes between checks

A: To ensure that the checks are randomized when completing the prescribed "minimum 4 checks per hour,…

Q: Compute the net quantities needed if there are 25 of the base and 75 of the clamp in stock.   ​Base:…

A: Here, First I would construct the product tree from the given information,  Here, I would assemble…

Q: As a requirement an IMS must have similarities when integrating different systems but with ISO 45001…

A: The question is asking about the changes that occur when integrating different systems under an…

Q: The results of the implementation were impressive. Vicunha was able to reduce lead times by 50%,…

A: The case study highlights the successful implementation of Toyota's Lean Production System (TPS) at…

Q: Do you have any ideas on how the machine's efficiency may be improved through interrupting,…

A: The efficiency of machines is a crucial factor in production planning because it directly impacts…

Q: Any unique product attribute that is not valued by the final customer is a waste that should be…

A: When products or services are manufactured or created, every business activity either adds value or…

Q: Workers have an ability to pull the Andon cord during the production process to prevent…

A: The name "Andon" stems from the usage of outdated lighting equipment, such as a fire-burning lamp…

Q: Component freedom means that one part should be able to be swapped out for another part that is made…

A: The idea of component freedom has become more significant when we try to evolve in a rapidly…

Q: With zero inspections we can know that the process is under control a. TRUE O b. FALSE

A: A process is said to be under control if it propagates within certain Upper and Lower control…

Lean Production

The word lean refers to the “slim “that is used in manufacturing for the systematic designing that focuses on minimizing the waste in the manufacturing or production with the constant productivity of the operation. Lean manufacturing was rooted from Toyota Production system a Japanese manufacturing company that works on the approach of minimizing the non-value-added activities and making the production lean.