A load P is supported by two concentric steel springs arranged as shown. Given the properties of the springs below, compute the maximum load that will not exceed a shearing stress of 150 MPa for the outer spring and 110 MPa for the inner spring

Q: Fundamentals of Deformable Bodies The frame shown in figure shows three pinned end bars AB, BD, and…

A: Note:- AB is not any bar according to the given figure, taking AD as a third bar A frame is given…

Q: A tubular aluminum alloy [G= 4,000 ksi] shaft is being designed to transmit 480 hp at 2,700 rpm. The…

A: Given values: Power, P = 480 HP Speed, N = 2700 rpm G = 4000 ksi = 576000 kip/ft2 Maximum shear…

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: shear force , V= 20 KN  thickness of all pieces= 30 mm

Q: Q1:- If the average normal stress in each of the 20-mm diameter bars is not allowed to exceed 150…

A:

Q: The internal diameter of a steel shaft is 70% of external diameter. The shaft is to transmit 3500 kW…

A: To determine: the diameter of the hollow shaft maximum angle of twist   Given, Power to be…

Q: The two vertical rods attached to the light rigid bar are identical except for ength. Before the…

A:

Q: The uniform rod is subjected to the axial loads as shown. Which segment has the absolute maximum…

A: Given Loads To find out Which segment has Maximum normal stress

Q: 75 mm 50 mm The compound shaft is attached to a rigid wall at each end. For the bronze segment AB,…

A:

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

A:

Q: The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the…

A:

Q: For the frame shown above is constructed out of circular tubes for both the beam and column.  It has…

A:

Q: Please consider

A:

Q: A stainless steel tube with an outside diameter of 60 mm and a wall thickness of 3 mm is used as a…

A:

Q: For the frame shown above is constructed out of circular tubes for both the beam and column.  It has…

A: Value of P can be calculated using the bending equation

Q: A)Determine the force in the 4-ft rod (in pounds). B)Determine the force in the 6-ft rod (in…

A:

Q: O 24,E 2 A,E 2 P 3 L. L

A: solution as the both the ends of the section is restrained so the displacement along x-directionwill…

Q: F1 (kN) 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A CLOSE COILED HELICAL SPRING IS TO HAVE A STIFFNESS OF 1 N/MM OF COMPRESSION UNDER A MAXIMUM LOAD…

A:

Q: For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to…

A:

Q: A steel shaft is loaded as shown. Knowing that T₁ = 1000 N.m, T₂ = 1600 N.m, L=250 mm, d 40 mm, D =…

A: Given: T1 = 1000N .m T2 =1600 N.m, L = 250mm , d =40 mm, D = 45mm Required : Maximum shear stress…

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: A

A:

Q: b D/ a В

A:

Q: As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm…

A: Consider the free body diagram

Q: 2m 1.Sm A For the given system below, rods A and B support the rigid bar, pinned at 0, as it is…

A: Free Body Diagram

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A:

Q: Problem 2 (for all students). Determine the state of stress, the principal stress and the max in-…

A: Calculating the moment of inertia: IP=π32504-404    The torque will be:T=6×300=1800 KN-mmThe bending…

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the…

A: Given:- A composite shaft fastened to rigid supports having Modulus of Rigidity as…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine loadP that can…

A:

Q: Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load…

A: To Determine Force in member AC, CD , DE

Q: Compute the average normal stress in each member of the truss below. Each member has a circular…

A: Given:Circular cross-section diameter= 0.75 inch Required:Average normal stress in each member

Q: The column is subjected to an axial force of 8 kN, which is applied through the centroid of the…

A:

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: Given:- V= 20 KN  thickness of all pieces= 30 mm  To find:- The maximum shear stress

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d…

A:

Q: The crane hook carries a load of 24 kN and the section at P-Q is rectangular as shown in the figure.…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15…

A: Given data:- W section W12×35 Axial load, P=10 kips Transverse load, V=15 kips Length of the beam,…

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur,  chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.