A load of 6,100 N + 1100 acts on the machine part shown in Fig. 5a. The machine part has a uniform thickness of 15 mm (i.e., 15-mm thickness in the z direction). Determine the normal and shear stresses acting at points H and K, which are shown in detail in Fig. 5b. For each point, show these stresses on a stress element. 10 mm -50 mm 50 mm 40 mm K B Fig. 5a 135 mm D 40° 40 mm Ho 15 mm Fig. 5b 40 m

A load of 6,100 N + 1100 acts on the machine part shown in Fig. 5a. The machine part has a uniform thickness of 15 mm (i.e., 15-mm thickness in the z direction). Determine the normal and shear stresses acting at points H and K, which are shown in detail in Fig. 5b. For each point, show these stresses on a stress element. 10 mm -50 mm 50 mm 40 mm K B Fig. 5a 135 mm D 40° 40 mm Ho 15 mm Fig. 5b 40 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Ox Txy Tyx Figure 1 Point Ax-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness of the element is 0.8 in., determine the combined normal stresses at points (a) and (f). 1.5 in. 1.5 in. Q2: For the stresses at the point shown, find: • The maximum shearing stress. The principal stresses and planes. B a ob c 10 8 in.- 8 in. f 90 MPa 30 MPa 6 kips 35° 8 in. 60 MPa
The rigid bar AB is hinged at A and supported by a steel plate hanger. The hanger is fixed at C and bolted at D with two plates.Given: Width of plate hanger= 50 mm Thickness of plate hanger = 10 mm Bolt diameter= 20 mm Allowable bolt shear stress= 68 MPaAllowable bolt bearing stress= 250 MPa a.What is the allowable stress in the hanger based on bolt capacity in double shear at D. b.If the maximum tensile stress in the hanger is 138MPa, find the allowable load W
The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 117,600 psi B A 6,650 psi A Cross Side |2,700 psi Section View (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use the sign convention for stresses acting on inclined sections.) max = psi psi 02 psi %3D ° counterclockwise from the +x-axis p1 p2 ° counterclockwise from the +x-axis
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Q/Normal and shear stresses acting at the point is shown in Figure 1- Determine the principal stresses and the maximum shear stress acting at the point . Show these stresses in an appropriate sketch . 2- If the element is rotated 30 deg clockwise then determine the normal stresses and the shear stress acting at the point . Show these stresses in an appropriate sketch .
Required information Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Given: P=7 kips. A 30 in. -1.25 in. В 12 kips 25 in. 0.75 in. Find the average normal stress at the midsection of rod BC. The average normal stress at the midsection of rod BC is ksi.
The rod has a diameter of 40 mm. Determine the state of stress at point A and draw the resulting 3-D stress element. 1500 N 600 N 300 mm 100 N-m 800 N 100 mm B
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Q-5: For the element with stresses as shown below, find: a. The magnitudes and directions of major and minor principal stresses b. The shear and normal stresses acting on a horizontal plane as shown below 8kPa 2kPa 75° 75° экра TH Jon OH 4kPa 30° Horizontal plane