A Load absorbs 10 kVA at a lagging power factor of 0.6. The complex power is: Select one: a. 2000+ j8000 VA O b. 6000 + j8000 VA Oc 8000 j6000 VA O d. 10000 VA

Q: Find the frequency in hertz.

A:

Q: A given load takes 40 kVA at 50% lagging power factor, while another load is connected in parallel…

A: Given: A load takes 40 kVA at 50% lagging power factor. Other load takes 80 kVA 86.7% lagging power…

Q: + 100 2K: -100 V- 0100V 0200V/ 300V 150V A 250V

A:

Q: a) Find the ICA load current b) Give the voltage Vab c) Calculate the total complex power on…

A: a) Find the ICA load current b) Give the voltage Vab c) Calculate the total complex power on voltage…

Q: 200/0°V L In the circuit in the figure; • Ly load draws 15 kVA with lagging power factor 0.6. • The…

A:

Q: The load resistance R in Figure is adjusted until it absorbs the maximum average power. Calculate…

A: Step-1->

Q: i(t) Find rms value of given current waveform. HAA 10 2 4 6 8 10 -10

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is applied to the circuit…

A:

Q: The variable resistor R in the circuit is adjusted until it absorbs the maximum average power. The…

A: The solution for given the problem can be achieved as follows.

Q: A voltage of 2500 is applied to an inductive circuit of impedance (5+j10)Q Determine circuit current…

A: Power factor is the ratio of true power by apparent power. The value of power factor lies in between…

Q: Is |L 20020°V, L Vs rms S. - In the circuit in the figure; • L1 load draws 15 kVA with lagging power…

A: complex power S =Scos(angle)+ S sin(angle) where S is KVA  and angle is power factor angle

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is applied to the circuit…

A: The total current supplied by the source is calculated as iT=eTzT where zT is the total impedance of…

Q: Q1/ Find the RMS value of lo in the unbalanced three-phase circuit. 0.40 j20 a 1.60 j4 A 780 1540…

A: The solution can be achieved as follows.

Q: For the following circuit, find P, Q and the power factor. Ijine bim

A:

Q: The following AC power source connected to two impedances and one resistive load. Analyze the…

A: The Given circuit is To analyze the circuit reactive components and reactive power developed…

Q: SINE(0 6Vp-p 1.5K) R₁ LL 2.5 mH 100 PL On the load, find the Power (P) in Watts (W) R A 180//180 Ω…

A: Given Data: A series RL circuit with, Peak-to-peak voltage Vpp=6 V Frequency f=1.5 kHz To Find:…

Q: For the circuit shown in figure beside, find the total average power delivered to the circuit? * J5…

A:

Q: Find the average power absorbed by the resistor R R-900

A:

Q: For the circuit shown in figure beside, find the total average ?power delivered to the circuit J5 2…

A:

Q: A lagging system with a complex load has a power factor of 0.75 and an applied voltage of 200V. if…

A: Given data, A lagging system has, Power factor cosϕ=0.75. Voltage, VL=200 V. Apparent power, S=10…

Q: A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin4000t) A is applied to the…

A:

Q: find average power of the voltage source 10Ω j10 2 -j5 -j2.4 2 j102

A: In this question , we will find average power from voltage source..

Q: If a load is leading, which statement is NOT true? a. The load is capacitive. b. It’s reactive…

A: We are given a MCQ and we need to select the correct option out of four given option.

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is plied to the circuit shown.…

A: A Non- Sinusoidal Voltage; e=20+15sin1000t+10sin3000t+5sin4000tTo find the total power=?Power=V2Z

Q: Find the rms values for v = 120 V sin(3771 + 15°) and i = 8.5 x 10 A sin(2nt + 65°).

A: In this question we need to find a RMS value of voltage and current .

Q: determine the current in each branch using Nodal Analysis

A: It is given that: Zx=100∠0°

Q: If the frequency were doubled, what would be the new impedance? R www R = 121 ohms XL = 41 ohms Xc =…

A: given here a circuit of RLC series circuit and asked to find the impedance of the circuit when…

Q: 8. For this circuit, find the current I₁. A) 5.87 + j0.88 A B) 6.35 + j1.41 A C) -48 + j24 A D) 2.27…

A:

Q: Obtain the magnitude of the current l, in Figure. express answer in amperes 5Ω 40/90° V τ 8Ω -j2Ω…

A:

Q: on A Load absorbs 10 KVA at a leading power factor of 0.6 The complex power is: Select one: O a…

A: The is a problem of circuits.  Given:- Load power |SL|= 10 kVA  Power factor, cos(phi)= 0.6 leading…

Q: A non-sinusoidal voltage (e=20+15sin2000t+ 10sin6000t+5sin8000t) Volt is applied to the circuit…

A:

Q: The total impedance in the polar form in ohm. The total current in polar form. The total power…

A:

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is applied to the circuit…

A: Given, e=20+15sin1000t+10sin3000t+5sin4000tThe RMS value of the voltage…

Q: Find the real and reactive power absorbed by each element in the following circuit. -j5 n HE + VE…

A:

Q: d. The rms value of load current equals to 10.8 A 7.64 A 2.4 A O 16.97 A

A: 19. The given data from the question is as follows: Single phase half wave uncontrolled…

Q: What is the capacitance to be connected in parallel with the load to increase the power factor to…

A:

Q: j100Ω -j500 ... ll 12 A (10+je)V 2000 (5-j5)V (2)

A: To determine the currents i1 and i2

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is ?applied to the circuit…

A: For this problem first we need to find RMS value of voltage and then current.

Q: A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t- 0.5sin4000t) A is applied to the…

A: Given iT=2+1.5sin100t+1cos3000t-0.5sin4000t A

Q: Find the total impedance of the circuit below. -j5 2 5 Ω { 32 100/0° V(A 5Ω j4 N 55/29 - j80/29 ohm…

A:

Q: Correct the power factor seen by the voltage source in the following circuit so that it is better…

A: It is given that:

Q: R1 400 L1 20mH R2 300 V1 R3 L2 20Vpk 60HZ 0° 30mH R5 1kO R4 250 100 C1 :100µF

A: