A liquid of density 1210 kg/m³ flows steadily through a pipe 7. of varying diameter and height. At Location 1 along the pipe, the flow speed is 9.91 m/s and the pipe diameter dị is 12.7 cm. At Location 2, the pipe diameter d2 is 17.3 cm. At Location 1 Location 1, the pipe is Ay = 9.39 m higher than it is at Location 2. Ignoring viscosity, calculate the difference AP between the fluid pressure at Location 2 and the fluid pressure at Location 1. Ay Location 2 ДР — Ра d,

A liquid of density 1210 kg/m³ flows steadily through a pipe 7. of varying diameter and height. At Location 1 along the pipe, the flow speed is 9.91 m/s and the pipe diameter dị is 12.7 cm. At Location 2, the pipe diameter d2 is 17.3 cm. At Location 1 Location 1, the pipe is Ay = 9.39 m higher than it is at Location 2. Ignoring viscosity, calculate the difference AP between the fluid pressure at Location 2 and the fluid pressure at Location 1. Ay Location 2 ДР — Ра d,

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter12: Fluid Dynamics And Its Biological And Medical Applications

Section: Chapter Questions

Problem 11PE: (a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per...

See similar textbooks

Similar questions

What is the greatest average speed of blood flow at 37° C in an artery of radius 2.00 mm if the flow is to remain laminar? What is the corresponding flow rate? Take the density of blood to be 1025 kg/m3.
Water is moving at a velocity of 2.00 m/s through a hose with an internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
(a) Suppose a blood vessel's radius is decreased to 90.0% of its original value by plaque deposits and the body compensates by increasing the pressure difference along the vessel to keep the flow rate constant. By what factor must the pressure difference increase? (b) If turbulence is created by the obstruction, what additional effect would it have on the flow rate?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant, as stated in the text. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
An incompressible, nonviscous fluid is initially at rest in the vertical portion of the pipe shown in Figure P15.61a, where L = 2.00 m. When the valve is opened, the fluid flows into the horizontal section of the pipe. What is the fluids speed when all the fluid is in the horizontal section as shown in Figure P15.61b? Assume the cross-sectional area of the entire pipe is constant. Figure P15.61
What is the difference between flow rate and fluid velocity? How are they related?
A U-tube open at both ends is partially filled with water (Fig. P15.67a). Oil having a density 750 kg/m3 is then poured into the right arm and forms a column L = 5.00 cm high (Fig. P15.67b). (a) Determine the difference h in the heights of the two liquid surfaces. (b) The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height (Fig. P15.67c). Determine the speed of the air being blown across the left arm. Take the density of air as constant at 1.20 kg/m3.
The flow rate of blood through 2.00106 -m-radius capillary is 3.80109 cm3/s. (a) What is the speed of the blood flow? (This small speed allows time for diffusion of materials to and from the blood.) (b) Assuming all the blood in the body passes through capillaries, how many of them must there be to carry a total flow of 90.0 cm3/s? (The large number obtained is an overestimate, but it is still reasonable.)