A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005m long at 20°C under a 50 N pull supported at both ends. During measurement the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured of 3% grade. What is the true horizontal distonco? F - 200 GRo croce-coo oroce-coctione1 onal

A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005m long at 20°C under a 50 N pull supported at both ends. During measurement the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured of 3% grade. What is the true horizontal distonco? F - 200 GRo croce-coo oroce-coctione1 onal

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need solution ASAP
A line was measured using a 30-m steel tape that is standardized at a temperature of 15°C and under a pull of 8 kg. If the temperature during the measurement was 25°C and the tension exerted 15 kg, determine the corrected tape length. The tape has a cross-sectional area of 8 mm², Modulus of Elasticity of 20000 kg/mm? and coefficient of thermal expansion of 0.0000112/°C.
X = 856 Y = 56 A = 8 B = 2 C = 5
Answer is letter B
Dont round off initial value, round off final ans
A steel tape is 30 m long at a temperature of 15°C and a pull of 50 N when laid on a flat surface. The tape weighs 18 N. It is stretched between end supports only allowing it to sag. Find the correct length of the tape at a field temperature of 25°C at a pull of 115 N. If in the above condition a base line is measured and the recorded length of the line is 600 m, find the correct length of the base line. Take a = 12 x 10-6 per °C and E= 2 x 105 N/mm². Sectional area of the tape = 7.50 mm².
A 10 load is uniformly cated by an aluminum alloy pipe with an outside diameter of 10 cm and inside diameter of 9.6 cm. The pipe is 1.2 m long. Young's modulus for the aluminum alloy in 7.6 x 10 MP How much the compet 04.00000 O 001 025mm
A 50-m steel has an error of 0.04 m at 20°C with a pull of 50 N. A rectangular lot is measured using this tape. The sides are recorded as 19.84 m and 10.21 m. The average temperature of the tape during measurement is 20°C with a pull of 50 N. The correct area of the lot in square meters is:
Q1)- A) compare by drawing between the Clay minerals of 1/1 and clay minerals of 1/2
YALVE 3) Constont level constent level k 0.26 O-63 soyuB 0.48m According to the above figure given 760 me rater is collected in the container in 15 minutes.If kA is giver as kA= 2x 10m/s..calculate the permeability of isoil B (kR).Length of the Systen perpendicaelar to the Figure plane (thickness) is coefficent O.15 m. -0.2m
I need handwritten neat and clean solution..I repeat handwritten solution with each step wise explaination, plagiarism free. I will upvote if you follow the instructions else get ready to get downvote. BEST OF LUCK
SHOW COMPLETE SOLUTION INCLUDE FBD AND FORMULA USED