Sharp-edgedentrancePipe AD= 200 cmL-28 m45° elbowScrewed, 2 in45° elbowScrewed, 2 in90° elbowFlanged, 2 inPipe BD- 100 cmL=10m 2Gate valveScrewed, finGlobe valveFlanged, 2 inHint: You will need to do iteration table will have the following columns: fa, fb, Va, Vb, Re,a Re,bA large, pressurized tank delivers water upstream via a series of two pipes as shown in thefigure. If the pressure at point 1 is 10 MPa and the elevation is given, determine the dischargeflowrate through the system. Elevation difference is 15 m. (Use vH2O= 1.00035 x 10-6 m2 /s,ε=0.0002 m).

Answered: Image /qna-images/answer/854435e7-cb22-4009-bdb5-cdd841ba6db5.jpg

A large, pressurized tank delivers water upstream via a series of two pipes as shown in the figure. If the pressure at point 1 is 10 MPa and the elevation is given, determine the discharge flowrate through the system. Elevation difference is 15 m. (Use vH2O= 1.00035 x 10-6 m2 /s, ε=0.0002 m).

A large, pressurized tank delivers water upstream via a series of two pipes as shown in the figure. If the pressure at point 1 is 10 MPa and the elevation is given, determine the discharge flowrate through the system. Elevation difference is 15 m. (Use vH2O= 1.00035 x 10-6 m2 /s, ε=0.0002 m).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
Water with density of 998 kg/m3 flows from a lake through a device inside the building at rate of 0.11 m³/s as shown in figure below. The piping system has length and diameter of 91.5 m, 0.12 m respectively. ● (1) Is the device inside the building a pump or a turbine? Justify your answer. Determine the horsepower of the ● device. Neglect all minor losses and assume the friction factor is 0.025. Lake Int 10 m
The water passing through the turbine of a hydroelectric power plant at a flow rate of 30 m3 /s is poured into the river bed with a velocity of V2=2 m/s. Head loss in turbine and pressure pipe is hk=20 m. Assuming the flow is turbulent and the kinetic energy correction factor α=1.06, find the power supplied by the turbine in MW.
Water flows steadily into the Venturi tube in the following figure. In the section considered, negligible friction losses and uniform properties in the sections are assumed. The entrance area (A1) is 20 cm2, while the throat area is A2 = 10 cm2. A pressure gauge whose manometric fluid is mercury (Yhg = 136,000 N / m3) is connected between the inlet sections and the throat, as seen in the figure. The flow of water that flows through the Venturi tube is requested (γH2O = 10,000 N / m3. Answer .: ϕ = 5.8 L / s.
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of the inverted tube is 1 meter above the free surface of the alcohol in the tank and 10.5 meters above the ground where the alcohol is discharged. Alcohol exits the tube at atmospheric pressure. The Specific gravity of alcohol is 0.89 while g= 9.81. The pressure, in kilopascal, in the bend is Blank 1 P=? 1m
The pump shown in the figure below produces a steady flow of 12 gal/s through the nozzle. Determine the nozzle exit diameter, D2, if the exit velocity is to be V₂ = 109 ft/s. D₂ = Pump i Section (1) Section (2) V₂ in
The pressure after the pump in a 6-inch inside smooth pipe conducting water is 20 psia. The water is dischargedat an open tank 100ft. from the pump. Calculate the rate of discharge of water in ft^3/s
The pumper truck shown in the figure below is to deliver 1.4 ft3/s to a maximum elevation h of 58 ft above the hydrant. The pressure at the 4-in.-diameter outlet of the hydrant is p-11 psi. If head losses are negligibly small, determine the power that the pump must add to the water. Assume D-4 in. W shall Hydrant hp
What is the minimum power required from the pump to deliver the oil from Reservoir A to Reservoir B as shown in Figure 2 at a rate of 0.30m³/s? The pump has a 70% efficiency rating. V Reservoir A -Oil v= 10-5 m²/s p=950kg/m³ Elevation 135m Steel Pipe, ks =0.046mm, L= 200m, D=250mm Elevation 120m r/D=0.1 Pump Figure 2 r/d=1 Reservoir B abrupt Globe valve, wide open Air at 200kPa Elevation 110m Elevation 100m
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
Water (ρ = 1000 kg/m3) is flowing vertically in the pipe shown below. The top, middle, and bottom parts have radii of r1 = 3 cm, r2 = 1 cm, and r3 = 3 cm, respectively. The speed of water flow and the gauge pressure at point 1 are v1 = 20 cm/s and P1 gauge = 200 Pa. The height difference between point 1 and 2, point 2 and 3 is 10 cm. Use g = 10 m/s2 for the acceleration due to gravity. What is the speed of the water flow at point 2? What is the gauge pressure at point 2? What is the speed of the water flow at point 3? What is the gauge pressure at point 3?