A kite is in the form of a rectangular airfoil with chord length of 60 cm and a width of 45 cm and weights 0.8 N. It is maintained at an angle of 10° to horizontal and the string makes an angle of 30° to the vertical. If the wind speed is 15 km/h and Co is 0.25 (given figure), estimate the tension in the string and the lift coefficient. [Pair = 1.2 kg/m³] 15 km/h 10° T FL W 30° Kite

A kite is in the form of a rectangular airfoil with chord length of 60 cm and a width of 45 cm and weights 0.8 N. It is maintained at an angle of 10° to horizontal and the string makes an angle of 30° to the vertical. If the wind speed is 15 km/h and Co is 0.25 (given figure), estimate the tension in the string and the lift coefficient. [Pair = 1.2 kg/m³] 15 km/h 10° T FL W 30° Kite

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need solve in 20 min please
If blocks A and B has the total mass of 250 grams with a ratio (A:B) of 2:3, what will be the smallest force F needed to cause motion of block B if P=300 N? Let the static friction of the surfaces between A & B and B & C will be 0.25 and the surfaces between the ropes and pegs D & E be 0.35.
SOLVE THIS USING CBM. THANK YOU. The roof beam of a building is subjected to the loading shown. If a 3/8-in. deflection is permitted at the cantilever end before the ceiling & roofing materials would be damaged, determine the required moment of inertia for the beam. Use E = 29,000 ksi. 24 kips 0.72 kip/ft 0.48 kip/ft B
A crane is used to lower weights into a lake for an underwater construction project. Determine the tension in the rope of the crane due to 3-ft-diameter spherical steel block (density = 494 bm/ft3) when it is (a) suspended in the air and (b) completely immersed in the water.
Q8
2. A beam having an 8 m simple span has a cross section shown in the figure. The beam is reinforced with 4 - 25 mm diameter bars. Determine the maximum concentrated load that his beam can carry beside its own weight. Fc = 7 MPa, fs = 124 MPa, n=10. 100 200 100 24 a po 400
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
Block P=5kg and block Q of mass m kg is suspended through the chord is in equilibrium position as shown in the figure.Determine the mass of block Q
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.38 in. when the tension in the rod is 2300 lb. If the diameter of the rod is 0.376 in., determine the maximum length of the rod. O 199.3 in. O 236.3 in. O 183.5 in. O 248.3 in. O 219.2 in.