A jet of water is flowing out of a square orifice in a large tank whose center is 600 mm below the water surface. If the orifice opening is 150 by 150 mm, what is the theoretical discharge in lps? Find the theoretical velocity in cm/s.

Q: A cylindrical tank having a diameter of 4m/s and 8m is full of water. There is an orifice at the…

A: Given data: diameter =4 m height =8m Area of orifice =0.02 m2 Cd=0.6

Q: A sharp edge orifice 105-mm diameter, in the side of a tank having a horizontal cross-section 2m…

A: d=105mm H2=2m Cd=0.6

Q: Orificemeter cpilejaye Two small circular orifice of diameters d₁ and d2, respectively, are placed…

A: Two small circular orifices- Diameters = d1 & d2. Depths of tank h1=25 cm & h2=1 m=100 cm,…

Q: A liquid of specific gravity SG = 1.62 flows in a 75 mm diameter horizontal pipe. The total energy…

A: Specific gravity of liquid, SG =1.62Diamteter of pipe, D=75mm =0.075mThe total energy at a point, E…

Q: A turbine, located at an elevation 255m below that of the water surface at intake, carries a flow of…

A: Given- E=255mq=3.5m3/sη=92%hf=10m

Q: The actual velocity in the contracted section of a jet of liquid issuing from a 5 cm diameter…

A: 1. Diameter of the orifice = 5 cm2. Actual velocity in the contracted section = 7.5 m/s3. Head…

Q: Find the power loss (in kW) when a fluid of dynamic viscosity = 1.2 Pa.s and p = 1150 kg/m3 flows at…

A:

Q: A nozzle of inner radius 1.06 mm is connected to a hose of inner radius 9.05 mm. The nozzle shoots…

A:

Q: 12-in diameter pipe is 1.60 ft./s, what is the velocity in a 2.5-in diameter jet issuing from a…

A: Using continuity equation :Q=v1A1=v2A2

Q: Water is flowing in a 90° triangular channel at a depth of 39 cm. A hydraulic jump occurs. The depth…

A:

Q: Water entering a pump through an 200mm diameter pipe at 27.6 kPa has a flow rate of 0.1 m^3/s. It…

A:

Q: shaft = 44 kW and mechanical efficiency 94%. Q53. The following data were obtained from a test on a…

A:

Q: A frustum-shaped body is rotating at a constant angularspeed of 200 rad/s in a container filled with…

A: Above given data we have to find power required and the reduction in the power due to increase in…

Q: d O2 placed at depths of 200mm and 800mm . in water , Calculate the diameter ratio

A: According to given data Discharge through Orifice , Q=CcaCv2gh…

Q: A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.55 mm. The nozzle shoots…

A:

Q: Pipe Length Diameter 1 947mm 250mm 583mm 275mm 3. 1026mm 180mm

A:

Q: aped that the velocity of flow a from 1.5 m/s to 15 m/s in a di magnitude of the convective a

A:

Q: A liquid flow through pipe of diameter 10 cm a velocity of 6 cm Find the value of discharge

A:

Q: A sharp-edged circular nozzle with a cross-sectional area of 10 cm2. Water flows from it under the…

A: Actual velocity calculation:…

Q: nozzle is so shaped that the average flow velocity changes linearly from 1.5 m/s at the eginning to…

A: Given velocity- V1=1.5 m/s V2 =15 m/s  Distance dx=0.375 m

Q: 1 velocity of V₁ = 1.7 m/s. The water in the pipe then exits vertically into the air. If the head…

A:

Q: 1. A cylindrical tank, 1.5m inside diameter has an orifice at its side 0.25m above the bottom. If…

A: Reference : Water resources, Orifices.Given :Diameter of orifice, height of water.To determine :1.…

Q: As shown in the figure, a hydraulic jump occurred at the end of spillway, the depth of water (2) and…

A: Depth of water after the jump (y2) = 11mVelocity of water after the jump (V2) = 2.9 m/s Determine…

Q: 10.8 For laminar flow in a tube calculate the position of the average cross-sectional velocity.…

A: Step 1

Q: What will be the discharge in L/s through a 25 mm orifice (C = 0.61) in the bottom of a tank moving…

A:

Q: A fire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X= 0)…

A: a) Using Bernoulli’s equation, Here, the pressure is atmospheric so the pressure p1 and p2 are…

Q: Calculate the discharge through a pipe of diame ter 200 mm when the difference of pressure head…

A: Given: Diameter of pipe, d = 200 mm = 0.2 m Length, L = 500 m Pressure head difference, hf = 4 m…

Q: A cylinder of internal cross-sectional area 2 sq.m. is submerged in a liquid to a depth of 1 m. The…

A: Given Submerged depth, b=1m Area of cross section of cylinder=2m2 Diameter of orifice=20mm Pressure…

Q: shaft = 44 kW and mechanical efficiency = 94%. Q53. The following data were obtained from a test on…

A:

Q: Application of Darcy Weisbach equation: A 24-inch steel pipeline (E= 0.016-in) 1550 feet long is…

A: Given: Diameter of th steel pipe, D=24 inchesArea,   A=π4×D2=452.39 in2Pipe's absolute roughness,…

Q: If the inner diameter of the penstock that deliver water form the dam to the hydroelectricpower…

A:

Q: Three pipes are connected in series with lengths and diameter given below. Solve for the total head…

A: Given that, three pipes are connected in series with lengths and diameter The total head loss has to…

Q: A 6-in-diameter cylinder falls at a rate of 2 ft/s in an 8-in-diameter tube containing an…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.