(a) In a certain lifting machine load of 100N is lifted by an effort of 8N and efficiency of the machine is 60%. Calculate the effort lost in friction and load lost in friction.

Q: The 46-lb load is hoisted by the pulley system and motor M. The motor exerts a constant force of 32…

A:

Q: QUESTIONS 1. What is the critical issue? What can be done about it? 2. Can excellence in project…

A: Any topic subject to the decision-making authority of any Committee that might have a major…

Q: 4. A particle weighs 17 lb and is moving as shown below at 8 ft/s. Answer the following questions.…

A:

Q: A 250mm plate of a 4340 steel is tested for quality control purposes. It fails at a stress of 550MPa…

A: given; ⇒for maximum toughness of plate (K1)=?⇒plate fails at stress (σ)=550MPa⇒internal flaw…

Q: 7) A 5-kg body A is released from rest on a frictionless circular surface. The body then moves on a…

A:

Q: Two blocks are connected by a massless rope over a frictionless pulley, as shown in the diagram…

A: Given data, frictionless pulley Ma = 2 kg  mass at block B Mb = 0.2 kg Angle of inclination θ= 30∘…

Q: 2. Draw the shear and moment diagrams for the cantilever beam.

A:

Q: A steel bar 200 mm in diameter is turned at a feed of 0.25 mm/rev with a depth of cut of 4 mm. The…

A: Given data: The diameter of the steel bar is D = 200 mm. The feed rate is f = 0.25 mm/rev. The…

Q: 2m Vc = 12 m/s The slider block C moves at 12m/s down the inclined groove. Determine the angular…

A:

Q: 4. The analyst in the Red Diamond Electronics Company wishes to assign a number of like facilities…

A: Given data: l=0.34+0.26=0.6 minutesm=1.48 minutesC1=$12 per hourC2=$18 per hourw=0.06 Need to…

Q: To reduce bit balling when drilling a soft clay formation, a PDC bit should have: Small journal…

A: 6. The bit balling can be reduced by proper bit selection, good hydraulic to clean the bits,…

Q: A gas inside a piston-cylinder assembly expands from P, = 6.5 bar, V, = 0.012 m³ to P2 = 3.3 bar in…

A:

Q: Q.1) Cables AE and CF are fastened to either side of a triangular plate to keep it from rotating…

A: Given Data: FAE = 55 N Find: a) Compute the moment about point D created by tension vector FAE…

Q: A vertical, frictionless piston-and-cylinder arrangement contains 2 lb of steam at 400 psia, 500°F.…

A:

Q: and material, explain why V-belt

A: a      Diary or plain course comprise of a shaft or diary which pivots unreservedly in a…

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: Solve the system the proposed mass-spring-damper system mä + cx + kx = 0 Use the initial conditions:…

A: Solution: Given Data: m = 8 kg c = 5 N-s/m k = 3 N/m

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E = 200…

A:

Q: Determine the maximum bending stress (psi) in the W250X115 beam. The beam is made from A36…

A: The beam is W250×115

Q: Ман Boiler WST WSP2 OFWH Qc WSP1 A power plant operates on a regenerative vapor power cycle with one…

A:

Q: A hollow steel drive shaft working in a high speed machine is shown in the figure and has an outer…

A: As per the guidelines, I can solve only first three subparts at a time. For other parts, repost in…

Q: At the instant shown, the angular velocity of the wheel is 2 rad/sec clockwise. Assuming that the…

A: Given data: Angular velocity of the wheel,  ω=2 rad/s Wheel rolls without slipping radius, r = 533…

Q: Find the mass moment of inertia, Izz, for the spherical ceramic femoral head ball (with a…

A: The radius of the sphere is r, The radius of the cylinder is r/2. The height of the cylinder is…

Q: mm and 300 mm, respectively, and the wall thickness of the cross sec = 0 kN/m to q = 4.2 kN/m for AB…

A: The free body diagram is-The moment equilibrium condition at point B is-

Q: 9) If the angular frequency of a wave is 0.7854 s and the wave number is 0.0785 m, then the water…

A: Given: Angular frequency of the wave is 0.7854 rad/s. Wave number is 0.0785 m-1.

Q: please answer all the parts to questions clearly from a-c

A: Phase diagrams are graphical representations that show the interactions between the various phases…

Q: (a) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing…

A:

Q: A dry-type general-purpose power transformer is observed to be operating above its rated tempera- to…

A: There are several possible causes for a dry-type general-purpose power transformer operating above…

Q: The R-ratio (minimum stress to

A: Given data; Determine the R ratio for this cyclic loading.During a high cycle fatigue test, a…

Q: Energy Conversion Problem 1. Atypical home uses about 30 kWh of electricity per day. The electric…

A:

Q: 6. Given the system shown below, design a value of K so that for an input of 100tu(t), there will be…

A:

Q: Steel is an alloy consisting primarily of iron, and has a carbon content between % and A % by…

A: Steel is an alloy consisting mostly of iron, with a carbon content between 0.2% and 2.1% by weight

Q: A force of magnitude P= 176 N is applied to the stationary machine handle as shown. Write the force…

A:

Q: a. What physical phenomena causes the pressure to drop from point 4-5 (and point 1-2)? b. Define the…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three parts of a…

Q: 1. The spring constant of each spring shown in the figure is k = 0.3 lb/in and the mass is 400 gram.…

A:

Q: What is the pipe area, A? Find flow velocity, V.

A:

Q: ted and concentrated torsional loadings shown. ine the absolute maximum and minimum shear on the…

A:

Q: The velocity amplitude of the vertical component of a surface wave, with a frequency of 5 Hz, is 3…

A: Angular frequency ω is larger than frequency ν (also called Hz) by a factor of 2π.Angular frequency…

Q: Figure Q4 shows the schematic for a pressure pad. The pad has area A and is connected to a rod of…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Problem 5: A student throws a water balloon with speed vo from a height h = 1.82 m at an angle 0 =…

A: Dear student,                    According to the guidelines I am allowed to answer only three…