A) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress factor higher than the stress concentration factor under static loading condition in or False concentration design. True B) If the same design safety factor is used, the reduction of the shaft diameter from 2" (inches) to 1" (inch) would cause the deflection of the shaft increases approximately ( ) times.

A) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress factor higher than the stress concentration factor under static loading condition in or False concentration design. True B) If the same design safety factor is used, the reduction of the shaft diameter from 2" (inches) to 1" (inch) would cause the deflection of the shaft increases approximately ( ) times.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spring balance is calibrated in an environment at a temperature of 25oC and has the following deflection/load characteristics Load (Kg) 0 2 Deflection(mm) 0 36 It is used in an environment at a temperature of 35oC and the following deflection/ load characteristics. Load (Kg) 0 2 Deflection(mm) 4 50 Determine ZERO DRIFT at 25oC ? ZERO DRIFT at 35oC ? ZERO DRIFT? ZERO DRIFT/oC?
The rotating shaft in the given figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 6 kN. Find the minimum factor of safety for fatigue based on infinite life. Be sure to check for yielding. 25 D. ] -35 D. 3 R. Dimensions in millimeters 500 -175- -50 D. 25 D. 20 20 20 180 280 20 What are the values of the theoretical stress-concentration factor, the notch sensitivity, and the fatigue stress concentration-factor? The value of the theoretical stress-concentration factor is The value of the notch sensitivity is (Round the final answer to two decimal places.) The value of the fatigue stress-concentration factor is (Round the final answer to three decimal places.)
Required information A shaft is loaded in bending and torsion such that M₂ = 66 N-m, T₂ = 42.496 N-m, Mm = 51.858 N-m, and Tm - 33 N-m. For the shaft, Su = 700 MPa and Sy=560 MPa, the true fracture strength is 1045 MPa, and a fully corrected endurance limit of S₂ = 210 MPa is assumed. Let Kf= 2.2 and Kfs=1.8. With a design factor of 2.0, determine the minimum acceptable diameter of the shaft using the methods mentioned in the subsection. Determine the minimum acceptable diameter of the shaft using the DE-Morrow criterion. The diameter of the shaft is mm.
* Question Completion Status: u(x) = N¡ ui + Ni+1 Ui+1 where: X1+1-X %3D and Ni+1 x-X Ix-+x Consider an element of length 1.85 (m) with node "" in origin. Consider a point at distance 0.33 L from the origin. Determine the value ofN1 for this point. QUESTION 19 Which failure criterion can be applied to brittle matenals? Select all applicable answers. O Tresca O Rankine All of the above OMises Submit to sqve and submit. Click Save AlILAnswers to save all answers.
None
2. A 1020 CD steel shaft (Sy=390 MPa) is used to transmit 20 kW of power at 1200 rpm. There are no bending or axial loads on the shaft. It is desired to have a static factor of safety of 2 based on the Distortion Energy theory. Determine the minimum diameter needed for the shaft. Power, P= To Pure torsion, relationship between T and t Torsional stress
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
i need the answer quickly
I need help solving this problem