A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 27ksi, determine the minimum force P required to punch the slot. Assume d = 0.75 in. and a = 3.75 in.aPlan view of slugPunchPlateSlugAnswer: P =ikips

Given:t=0.60 inζ=27 ksid=0.75 ina=3.75 in

Answered: A hydraulic punch press is used to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Tie rod (1) diameter = 11 mm, and it is supported by double-shear at B and D and single-shear at A. pin at B diameter = 9 mm a = 630 mm, b = 315 mm, h = 390 mm, and 0= 65°. allowable axial stress in tie rod (1)=210 MPa allowable shear stress in pin B =110 MPa WHAT IS THE MAXIMUM FORCE P? ANSWER IN KN ROUNDED-OFF TO 2 DECIMAL PLACES D (1) h a B b P
Please answer number 1 with step by step solution
The two square cross sections shown below (Figure 1) are each subjected to a vertical shear force, V. The side length of each cross section is s = 5.00 inin and the side length of the hollowed-out portion of the second cross section is r = 2.50 inin . The maximum allowable shear stress in each member is τmax = 19.0 ksi. One of the first steps in analyzing the geometry of the solid square shaft is to determine the moment of the area A’ about the neutral axis of the entire cross section. This value is denoted by Q. What is Q?(Figure 2) Answer is 15.625 in^3 A.) One of the first steps in analyzing the geometry of the hollow square shaft is to determine the moment of the area A’ about the neutral axis of the entire cross section. This value is denoted by Q. What is Q?(Figure 3) B.) Determine the maximum applicable shear force on the solid square shaft, Vmax. C.) Determine the maximum applicable shear force on the hollow square shaft, Vmax. In the image provided, figure 1 has a white slash…
For the figure shown below. Find the maximum allowable value of P if the bending stresses are not exceeding 3.5 KN/m² in tension and 8KN/m² in compression 0.015m 0.015m 2P |4P ЗР 0.2m . 0.25m 0.02m 2m A A 2m.
A hydraulic punch press is used to punch a slot in a 0.30-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 36 ksi, determine the minimum force P required to punch the slot. Assume d = 1.25 in. and a = 2.25 in.
Calculate the principal stresses and angles and the in-plane maximum shear stresses and angles for the loading condition given in the figure by using both analytical formulas and drawing Mohr's circle. G (MPa) -20, GY (MPa) —30, тхY (MРа) -60
P-2 kN d- 60 mm Q= IkN 600 mm 1m Calculate the safe shear stress value of the shaft, given that the smallest allowable diameter d of the shaft subjected to forces P and Q is given as 60 mm in the figure?
a 4ll Asiacell Q2 A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E for bronze = 100 GN/m2. Where SN=3 إجابتك
مقاومة المواد

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 27 ksi, determine the minimum force P required to punch the slot. Assume d = 0.75 in. and a = 3.75 in. a Plan view of slug Punch Plate Slug Answer: P = i kips